S2Forum - The Audi S2 Community

Go Back   S2Forum - The Audi S2 Community > Member's Area > Projects

Reply
Thread Tools Display Modes
Unread 24-12-16, 07:56 AM   #271
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Steering power cooling system was leaking... So finally I had time to repair it.. Checked with air compression and should be ok..




Then it was good time to put new TPS on place... The screw below was really ''nice'' to put back.. Especially when you have elephant fingers.. I managed to lose both screws... So I ordered new ones.. Then I lost one new one and while searching it, I found the old one...




Inlet temperature sensor also found its place.

Attached Images
File Type: jpg roolivõim.jpg (153.7 KB, 539 views)
File Type: jpg roolivõim 1.jpg (98.6 KB, 538 views)
File Type: jpg TPS.jpg (128.2 KB, 544 views)
File Type: jpg TPS 1.jpg (90.4 KB, 531 views)
File Type: jpg sisselaske temp.jpg (112.9 KB, 536 views)
maiks is offline   Post Tools
Unread 29-12-16, 06:31 AM   #272
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Santa was late..
Attached Images
File Type: jpg DSC01519.jpg (152.4 KB, 488 views)
maiks is offline   Post Tools
Unread 11-01-17, 06:34 PM   #273
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
I made pressure test to exhaust... So, like I thought, EM to turbo still leaks... This thing has been annoying me since I bought the stainless manifold.
So I took off the Em, turbo, wastegate and downpipe.
And changed the stainless flange to steel..



And again new ex wrap



Very stupid job to do.. Luckily I had one cold beer.. And an hour of free time..
Not an art work, but no radiator needed..
There is 15m wrap, 10m one piece



Attached Images
File Type: jpg DSC01566.jpg (161.7 KB, 443 views)
File Type: jpg DSC01559.jpg (251.6 KB, 441 views)
File Type: jpg DSC01560.jpg (249.4 KB, 442 views)
File Type: jpg DSC01537.jpg (179.0 KB, 444 views)
maiks is offline   Post Tools
Unread 13-01-17, 03:29 PM   #274
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Painted IC and pipes.. (Plastidip)



Oil cooler.
Before



After.



And a little more.. Home made engine mount.
Before



After

Attached Images
File Type: jpg cooler ja torud.jpg (142.5 KB, 420 views)
File Type: jpg õli radikas 1.jpg (111.6 KB, 413 views)
File Type: jpg õli radikas.jpg (134.5 KB, 419 views)
File Type: jpg mootori käpp 1.jpg (217.7 KB, 417 views)
File Type: jpg mootori käpp.jpg (142.1 KB, 416 views)
maiks is offline   Post Tools
Unread 16-01-17, 04:33 PM   #275
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Attached Images
File Type: jpg cooler ja torud.jpg (136.5 KB, 376 views)
maiks is offline   Post Tools
Unread 16-01-17, 08:15 PM   #276
Kiku
S2Forum Addict
 
Estonia
 
Kiku's Avatar
 
Join Date: Aug 2010
Posts: 320
Good reading and best of luck on the build. What ecu are you running? Original motronic? Modded by Prj?
__________________
1990 2.2 20VT Audi Coupe Quattro
*Hx35/k26, MaxxECU, Wagner EM/IC *RS2 Recaro *4pot-Brembo *3" turboback *Treser *Koni/H&R
1990 Audi 200 20v Avant 2.2 20VT *7 Seater *Full electric gizmos
Kiku is offline   Post Tools
Unread 17-01-17, 02:28 PM   #277
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Quote:
Originally Posted by Kiku View Post
Good reading and best of luck on the build. What ecu are you running? Original motronic? Modded by Prj?
Thanks. Yes, original mototronic and Dmitri mapped.
maiks is offline   Post Tools
Unread 18-01-17, 05:13 PM   #278
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
And the other side...
I think I'll make something to avoid crap going to the bov. I really like its position because it is not seen under the bonnet. I like the clean look.
Attached Images
File Type: jpg plow off.jpg (128.7 KB, 340 views)
maiks is offline   Post Tools
Unread 22-01-17, 02:47 PM   #279
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Painted the exhaust manifold and downpipe wrap.

https://www.youtube.com/watch?v=0SbeKfbglG4



Attached Images
File Type: jpg DSC01616.jpg (114.9 KB, 287 views)
File Type: jpg DSC01617.jpg (226.3 KB, 287 views)
File Type: jpg DSC01618.jpg (171.8 KB, 286 views)
maiks is offline   Post Tools
Unread 25-01-17, 05:30 PM   #280
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
If someone does not understand how I found out that my EM flange was bend.



Also replaced driver door hinge. On one good day, if I have time, I'll take it off and paint it also.
Replacing time was 15 min.



Here you can't see it, but the car nose is lifted up and with the old hinge the door didn't stay open, but with new hinge there is no problem.



To have access to one bolt, I needed to take off the wheel and remove some plastic.

Attached Images
File Type: jpg sumpa.jpg (100.1 KB, 239 views)
File Type: jpg ukse hing.jpg (178.4 KB, 239 views)
File Type: jpg uksehing1.jpg (160.2 KB, 240 views)
File Type: jpg uksehing2.jpg (158.2 KB, 234 views)
maiks is offline   Post Tools
Unread 26-01-17, 12:19 AM   #281
macspring
S2Forum Zealot
 
Home Country - Ireland Current Country - Western Sahara
 
Join Date: Mar 2005
Posts: 5,934
Fresh door hinges are cool the way the door stays open properly and doesn't 'drop' when opened.

Like a new driver's seat belt or a cleaned driver's seat belt - It retracts quickly and fully like a new car.

Enjoying the updates.





macspring is offline   Post Tools
Unread 28-01-17, 09:14 AM   #282
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Turbo has melted a hole..


New OEM


Changed
Attached Images
File Type: jpg DSC01624.jpg (190.4 KB, 202 views)
File Type: jpg DSC01627.jpg (137.3 KB, 203 views)
File Type: jpg DSC01631.jpg (112.2 KB, 200 views)
maiks is offline   Post Tools
Unread 28-01-17, 02:35 PM   #283
Vorsprung durch Technik
S2Forum Possessed
 
United Kingdom
 
Vorsprung durch Technik's Avatar
 
Join Date: Jun 2007
Location: Herts/Bucks/middx borders
Posts: 3,903
Garage
Really good to see a URS6 thread like this one with all the great work your doing!
__________________
96 URS6 plus speck saloon
96 URS6 plus speck estate
94 2.6 80 Avant
99 2.8 final edition Cabriolet
Vorsprung durch Technik is offline   Post Tools
Unread 29-01-17, 11:29 AM   #284
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
Thanks
maiks is offline   Post Tools
Unread 30-01-17, 06:37 PM   #285
maiks
S2Forum Addict
 
Estonia
 
maiks's Avatar
 
Join Date: Dec 2014
Posts: 248
I made a heat shield also to avoid plastic melting..
Used copper plate because it is soft and very easy to work with (rubber hammer).
Between plastic and copper should be 1 cm room, so hope it works.

Attached Images
File Type: jpg vask.jpg (122.2 KB, 127 views)
maiks is offline   Post Tools
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 07:22 AM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
DTO Garage vBulletin Plugins by Drive Thru Online, Inc.
©2003-2016 S2forum.com. All Rights Reserved.