Tweet
Built front chassis cross member, to reconnect where the front clip was cut out, even though I have the bottom cross member, which ties everything together along with the top piece, I wanted to make things really strong, so now I have (6) connections tying the front back together. The bottom cross member and front are bolted together, to really make it strong.
-
-
Hit a major mile stone and fired the engine and boy does it sound good.
Past few weeks have been a roller coaster trying to get the engine to fire. It took Norbert (SRS), Varia, Jeff (engine builder) and my buddy (Nils) to help diagnose the little issues......I would be lost without there help. Nils who is in California and I'm in Tennessee, remotely went through the setup on the Motec, calibrating sensors, throttle pedal etc. and mapped a base tune until the car can be driven.
Next is to lift the car and idle through the gears and check the drive train.
I tried uploading videos and they came out as pictures, is there away to upload videos?
Last edited by Blagave; 29 August 2024, 22:55.Comment
-
Link on YouTubeNothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
YouTube is above my pay scale.
Here is a link to my Instagram that has the motor running
https://www.instagram.com/p/C_RJTzspwvb/?img_index=1
Comment
-
Sounds awesome
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Hit another mile stone, tested the drive train.
When I installed the engine and trans awhile back, I spent a great bit of time trying to get the shifter linkage correct and thought I had done so........well, I was wrong. What I thought was reverse was 1st gear...ugh.
With some guidance from Mark (EFI) and Varia, I was able to get reverse and all the gears working smoothly. One of the issues was the metal shift guide form the C4 shifter, the metal where the hole is cut out for depressing the shifter for reverse was to straight up and down not allowing for full rotation on the shift rod to engage reverse, plus adjusting the linkage better.
Since my car is not being built as all original
, I took the liberty of cutting a 3" section out of the top of the tunnel to access the bolt to adjust the shifter rod otherwise, I would have to take off the drive shaft and exhaust. I used the piece I cutout and welded flanges all the way around so it can be a removable cap. I added hush mat on top and bottom and used sheet metal clips and screws to re-attach. In the future, if I need to adjust the rod, I can access through the top of the center console, which I am modifying and will share later.
Comment
-
Since my build is a bit of a hybrid, using the 1986 Coupe GT body harness and fuse box along with digital dash that Pete is refurbing for me, I purchased the Plex 330 digital display that links up with the Motec ECU to provide much more engine information than the Audi digital dash could ever provide. The display comes with GPS for speedo and will do lap times if desired. The screens are adjustable for what ever info you want displayed and has a few different screens you can access with the button pad
I removed the digital volt/temp display out of the center console and made aluminum face plates for the Plex display, push button pad for display, window switches and aux lights. Everything fits nicely and can be removed easily if I need to get to the tunnel cap I made to adjust shifter.
Comment
-
-
-
Just finished up the fuel pump relay upgrade. I used the same style fused relay as the fan and mounted it in the trunk.
I was contemplating on moving the battery to the trunk and decided to leave it as is under the rear seat, but ran cable from the battery to a two piece quick connect in the trunk, where I can attach a jumper cables or battery tender without accessing the battery.
Comment
-
Very tidy!!1996 S2 ABY Coupe silver
2003 S3 8L dolphin grey
2014 RS4 B8 prism silverComment
-
Sometimes you have to go backwards to move forwards.
1. Re-plumbed the engine venting, picking up both breathers on the top of the valve cover and venting to a K&N filter tucked behind the passenger side bumper space. I'm using the Porsche breather canister that does not have its own external breather like some of the others. I did not want the fumes staying in the engine bay, so hopefully this configuration will work out.
2. I reconfigured my fuel lines, which changed the position of the E85 sensor. I made a new mount for both the boost controller and E85 sensor, which worked out nicer than the old mount.
Comment
-
Made a cover for the motec ECU. I welded a couple of zeus tabs on the cage and used aluminum for the cover. I still need to clean up the wiring and the cover will get carpet to blend in with the foot well.
Comment
-
Clutch pedal had some slop and found the bushing was completely worn out that connects the slave cylinder rod. I used some brass and turned a new bushing, worked out great.Comment
-
A bunch of little things are being addressed. I could not find the mount for the battery, so I made one.
Comment
Comment