S2 stopped on highway - low oil pressure -help needed

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • EvenM
    replied
    Originally posted by Monkeymagic
    Have you pulled the fault code
    Yes, but the fault come and go, so when I Pulled the codes, nothing showed, other than g62? Coolent sensor something, that I dont think have something to do with this

    Can try again tomorrow

    Leave a comment:


  • Monkeymagic
    replied
    Have you pulled the fault code

    Leave a comment:


  • EvenM
    replied
    Now the car is shopping when get hot , aprox 15 min after startup. Can g40 cam sensor be the culprit ?

    Leave a comment:


  • Monkeymagic
    replied
    Could it not simply be that you have a ignition/sensor fault that has caused the engine to cut out, rather than an oil pressure issue. Once it has then the oil warning light will blink.

    Leave a comment:


  • EvenM
    replied
    Originally posted by 20Vcqdriver
    Not me personally, but I know of someone who lost oil presure, not enough to cause knocking but low enough to barely register on the gauge and the oil pressure relief valve had stuck or spring snapped (it was over 10 years ago now). He thought the worse regards oil pump but these don't tend to fail instantly. Suspect this especially if it was the gauge that dropped as engine cutout is normally activated from the pressure switch not the sender for the gauge, but will check this as its been a while and lots of water passed under the bridge..
    Thanks for the information Please update me if you find out more

    Leave a comment:


  • 20Vcqdriver
    replied
    Not me personally, but I know of someone who lost oil presure, not enough to cause knocking but low enough to barely register on the gauge and the oil pressure relief valve had stuck or spring snapped (it was over 10 years ago now). He thought the worse regards oil pump but these don't tend to fail instantly. Suspect this especially if it was the gauge that dropped as engine cutout is normally activated from the pressure switch not the sender for the gauge, but will check this as its been a while and lots of water passed under the bridge..

    Leave a comment:


  • EvenM
    replied
    thanks, this is a strange one, but hopefully I will figure out whats causing this



    Originally posted by mackenzie50
    So Always something after winter storage




    oh yes indeed...or just a few weeks of inactivity- had a bit of drama getting mine to fire up again this week...thankfully it did eventually.
    Good luck with finding your issue
    Oh, good to hear it fired up eventually, what was wrong ?

    Leave a comment:


  • mackenzie50
    replied
    So Always something after winter storage

    oh yes indeed...or just a few weeks of inactivity- had a bit of drama getting mine to fire up again this week...thankfully it did eventually.
    Good luck with finding your issue

    Leave a comment:


  • EvenM
    replied
    Any suggestion to what kind of electronic fault that can stop the car while running when the oil pressure light comes on?

    Leave a comment:


  • EvenM
    replied
    Originally posted by Rikki Kitto
    I know this for a fact
    Not good

    Leave a comment:


  • Rikki Kitto
    replied
    Originally posted by Pirvu Eugen
    Nope! You can run the engine without oil pressure until destruction!!
    I think is something electric.
    I know this for a fact

    Leave a comment:


  • EvenM
    replied
    Originally posted by Henkjan
    what fault codes did you see ?
    Pulled the codes today, none regarding this issue.

    After that I turned the engine, it started, and the oil pressure boosted right up to 5 bar on the guage in the car. So everything seems normal again, weird...

    So I think it have to be a electronic fault.. Always something after winter storage

    Leave a comment:


  • Henkjan
    replied
    what fault codes did you see ?

    Leave a comment:


  • Pirvu Eugen
    replied
    Originally posted by rustybullethole
    Im sure the ECU looks for initial oil pressure to give permissive to start engine or am I dreaming?
    Nope! You can run the engine without oil pressure until destruction!!
    I think is something electric.

    Leave a comment:


  • rustybullethole
    replied
    Im sure the ECU looks for initial oil pressure to give permissive to start engine or am I dreaming?

    Leave a comment:

Working...