6 Speed into an Ur Quattro

[my2000apb]

You need to shave 3mm from the inside of the flange (spline end).

That's all.

on the inside spline end there is a tapered cone just liek on the inside of the cup for the fixing bolt.

can the spline be cut shorter and flat? or do i need to lathe that cone farther into the spline as well?

[ralleyquattro]

You need to shave 3mm from the inside of the flange (spline end).

That's all.

[my2000apb]

heres the pic LMK what ya think about it sticking out too far

[my2000apb]

martin, just a few things i need get sorted
i am using an usdm urS4 5 speed o1e

i now have the 4kq outer cv's on b3 front axles
( are they coupe and 90 axles same length? and also side to side?)

the front drive cups are 4kq front 016 units in the o1e

it seems as though they stick out too far from the box, the drivers side 4kq/90 axle works but seems jsut a bit snug and the passenger wont quite fit even with the balljoint fully extended

heres a pic of the axle cups, lmk if you think they are stickign out too far

are the urS4 o1e's and b5 6speed o1e's the same width?

ill get a pic here soon

[my2000apb]

I just put in digidash, but if you read the article it will explain how to get the mechanical components in there (all 4kq stock parts).

Hope this helps

cool

we are currently working on using a 5ktq speedo in the 4kq clsuter for elec speedo

[ralleyquattro]

I just put in digidash, but if you read the article it will explain how to get the mechanical components in there (all 4kq stock parts).

Hope this helps

[my2000apb]

are you guys retrofitting the mechanical speedo into the o1e or going elec speedo on the dash w a 5ktq unit?

[ralleyquattro]

File too big, have to send via e-mail to those interested, Soz

The article is great and was very helpful to me but there are few things that can be done easier and quicker.

The shifter gate, no need to weld anything, combination of Ur-q and UrS4 parts can be bolted together with the same result, pics on my project page.



The shifter, same here, Ur-q shifter fits with ur-q ball on the UrS4 selector BTDT, no hitting of the floor or transmission, pics on my project page.

S2 6-speed mounts can be used with spacer on the pass side, no need for custom mounts.
Also, there is enough movement in the driveline and CVs that a 15 mm spacer for the back of the transmission is not needed.

I have a copy of the article on my site:

http://www.quattro.ca/6%20speed%20article.pdf

Hope this helps
Martin

[madpugger]

email it to me... I'll host it and post link

[20Vcqdriver]

scan the article and post the PDF here please?

File too big, have to send via e-mail to those interested, Soz

[driftin jo]

The six speed is not as strong as the quattro box

If you switch your clutch and flywheel is all S2.

You need to bring over the linkage as well. This means adapting the tunnel

Early 6 speeds are weak. The later ones much better

If you want proper robust then an RS4 2.7T box can be made to fit or even an All Road if you can find one

Early 6 speed is still stronger than the ur box

[s4boy]

Please could I have a copy of the article also...........thanks mark..

[quattrostyle]

scan the article and post the PDF here please?

Already forwarded it to you

[Bram]

I have my Audi Driver article on the swap into a 1986 coupe quattro if it helps. A few differences if fitting to a Ur but you'll get the basic jist of the work involved. Send E-mail address in a PM if you want it.

scan the article and post the PDF here please?

[RS2000WRC]

I have my Audi Driver article on the swap into a 1986 coupe quattro if it helps. A few differences if fitting to a Ur but you'll get the basic jist of the work involved. Send E-mail address in a PM if you want it.

pm sent