MOT Disaster!

[Error404]

the easiest way to apply it is with a sponge applicator i've found, gives a nice finish... but really, noone cares about the finish on your subframe....

EDIT: actually, this IS Steve's thread....

[Jamo]

I can't believe it a detailing thread on POR-15

Por15 is not UV resistant so if you want it to last i.e look pretty then top coat it after application.

[AndyP]

You don't really get brush strokes with POR-15. It's very thin and as long as you're careful it paints on nicely and gives a very even finish. Two thin coats was enough for my subframe!

I agree, I've brush painted POR15 and it was as smooth as silk when dry. Plus I've read that when you thin it to spray it reduces it's chip resistance.

[S2central.net]

Has got a bit like that - guilty as charged for my part m'lud...

[Fat Audi 80]

I can't believe it a detailing thread on POR-15

Por15 is not UV resistant so if you want it to last i.e look pretty then top coat it after application.

I just want to find the best way to do it once and do it right!

I won't be putting mirrors under my car or anything.....

[Jamo]

Lol that was a serious comment btw PO-15 is not UV resistant you can top coat it with enamel to keep it looking good. Says so in the instructions

[Fat Audi 80]

It won't me seeing much UV sitting in my garage for 99% of the time though will it?

Thanks for your input though, I will double check its suitablility.

Cheers,

Fatty.

[merlin's S4]

I agree the POR-15 rust prevention paint that Steve linked to is not UV resistant so should be top coated when used in areas exposed to direct sunlight. Unless you're planning on driving the S2 upside down I can't see a problem!

The POR-15 Chassis coat is UV resistant and can be used to top coat the above product for a super tough finish. However I think Steve's already planning to use Hydrate 80 as a base coat which is very good stuff, so IMHO those two products combined with the Dynax in the cavity will be enough to provide an extremely long lasting protection.

[S2central.net]

I would top coat it - just for extra protection.

[bigdan]

I cleaned mine back, treated it with Loctite 'Rust Remedy' (even though it wasnt rusty!) then painted it with outboard engine primer and paint!

Different, but i did it about 4 months ago and its holding up well!

[Fat Audi 80]

Thanks for offering a different option.

I just want to get it back on the road as quickly and inexpensively as possible whilst providing enough protection for the rest of its (garage queen) life.

[Crawford_S2]

Ah dude, just catchin up with your thread after rain stopped play on my project, wiring and rain doesn't mix! Cannot believe your coupe has rotted in its sealed bubble, lucky you don't use it and abuse it like most of us or the subframe would be hangin outLol!

Know how you feel though, found a hole in my caddy whilst under it fitting the new engine, more welding but was going to be under it making the exhaust anyway so will bosch in a plate at the same time.

Good luck, race is on for inters, i am in the same boat but sounds like you are slightly closer to getting yours there. Only got mine started yesterday!

[Fat Audi 80]

Thanks Crawford,

The race is most definitely on! All being well I *should* be okay, the subframe is sound apart from the hole! I also have the fuel lines to do and am ordering the parts up for that today.

As long as I can get it all apart (there are some rusty bolts under there) I think I will be okay....

Fingers crossed for you too.

Cheers,

Steve.

[mark_s2]

PM sent re. the media blaster in Reading

[Fat Audi 80]

I bought this in the end as it was in stock!

http://www.frost.co.uk/item_detail.a...tID=&SubCatID=

Should do the trick...