RS2 3mm spacers needed.

[rs2315]

Just wanting some advise on spacers.
Never used them before.

The front hub is OE with small reds if that info is needed.

I,m fitting 18" MTM cup 1's with 245 -35 tyres to my RS2, I beleive the rears are just bolt on, very close to rear arms but o.k.
The fronts I've been told need 3mm spacers to avoid rubbing.

GT500 run's this set up. I could ask him, but he gets enough questions from me, so I thought I'd leave it to the panel.

Just want to know what make to use Fordge H&R, any others??
What info do I need to pick the correct spacers for the set up I've described above.

Ta very much to any info.

rs2315.

[Big Lee M]

For a start they need to be 5x130 and the right centre bores as they are different to Porsche ones as far as I know. I doubt forge do them for the RS2.

[Tonks4x4]

Send Bambridge a PM he will knock a set up for you to whatever spec you want.

[Lloyd]

You do not need spacers, they bolt right on.

[GT500]

You do not need spacers, they bolt right on.

Not with wide 245s. Some are alot wider than others. Steve has federal 595 rs to go on.

I got some from what was Larkspeed in cleck.

[Thuppu]

I can lasercut spacers for you with any specs you want(1-10mm thickness).

[rs2315]

Right chaps thanks for the replys.
I've decided to go with Tonks suggestion and I've pm'd Bambridge.

The info Kev requires.

"Max diameter of the front hub, and the diameter of the spigot to get the bore right.

If anybody has this exact info please could they post it up.


In Lee's post he mentions 5-130, what is this measurment?

Cheers
rs2315.

[rs2315]

I can lasercut spacers for you with any specs you want(1-10mm thickness).

Thanks for your offer of help Thuppu

As mentioned I'm going to use Bambridge for this.

rs2315.

[Tonks4x4]

5x130 is the PCD of the wheel studs.

[jade]

Just wanting some advise on spacers.
Never used them before.

The front hub is OE with small reds if that info is needed.

I,m fitting 18" MTM cup 1's with 245 -35 tyres to my RS2, I beleive the rears are just bolt on, very close to rear arms but o.k.
The fronts I've been told need 3mm spacers to avoid rubbing.

GT500 run's this set up. I could ask him, but he gets enough questions from me, so I thought I'd leave it to the panel.

Just want to know what make to use Fordge H&R, any others??
What info do I need to pick the correct spacers for the set up I've described above.

Ta very much to any info.

rs2315.

Whats the offset of the wheels ? I am fitting et52 with the same size tires maybe hancocks wandering if I will have the same problems I might need some also

[GT500]

They are et 52 and 8.5 wide. Not tried Handcocks but some 245s are alot wider than others.

Steve you need centre bore of 71.3 5x130 and do a quick measure of the disc face for the external diameter.

[rs2315]

They are et 52 and 8.5 wide. Not tried Handcocks but some 245s are alot wider than others.

Steve you need centre bore of 71.3 5x130 and do a quick measure of the disc face for the external diameter.

Ta Rob, I'll measure disc face tomoz.

rs2315.

[rs2315]

5x130 is the PCD of the wheel studs.

Thanks for that Tonks.

rs2315.