exhaust header for 20v Audi

[Hacke]

hello!! i makes exhaust header for 20v Audi

pictures

http://200sx.kicks-***.net/miss_nism...218cca164a.jpg

http://200sx.kicks-***.net/miss_nism...218efd71a8.jpg

http://200sx.kicks-***.net/miss_nism...95c332ffcb.jpg

pris for the haeders above: 820 $

http://200sx.kicks-***.net/miss_nism...52f9-thumb.jpg

pris for the small one: 700$

http://200sx.kicks-***.net/miss_nism...aa3f-thumb.jpg

intressted?? mail me for more info: rs3_syncro@hotmail.com

[Wizard-of-OD]

hello!! i makes exhaust header for 20v Audi

pictures

http://200sx.kicks-***.net/miss_nism...218cca164a.jpg

http://200sx.kicks-***.net/miss_nism...218efd71a8.jpg

http://200sx.kicks-***.net/miss_nism...95c332ffcb.jpg

pris for the haeders above: 820 $

http://200sx.kicks-***.net/miss_nism...52f9-thumb.jpg

pris for the small one: 700$

http://200sx.kicks-***.net/miss_nism...aa3f-thumb.jpg

intressted?? mail me for more info: rs3_syncro@hotmail.com

[diesel des]

I was very tempted by your manifold hacke. Wish i could weld like that! But I just have got in on a group buy on the RS tuning manifold. Its more expensive than your part, but thats the way the group buy went. Thanks,des.

[Stick Insect]

pictures ...
http://200sx.kicks-***.net/miss_nismo

Should read
pictures ...
http://www.200sx.kicks-***.net/miss_nismo

HTH

I love your welding....

David

[Sidspud]

Both work equally well on my system.

[Stick Insect]

Both work equally well on my system.

Try the first post in this thread, that one doesn't work for me.

David

[Hacke]

I was very tempted by your manifold hacke. Wish i could weld like that! But I just have got in on a group buy on the RS tuning manifold. Its more expensive than your part, but thats the way the group buy went. Thanks,des.

ok.. more expensive and still second best..

[diesel des]

Hacke, i was just worried that the angle your wastgate leaves the collector at seems tight. I dont know much about these things, but some of the other "experts" thought the RS unit would be slightly better. But Yours looks much more sexy to me.

Des, having second thoughts

[diesel des]

Hacke do you make those inlet manifolds too? How much are they? Would it fit a UR quattro with a ABY engine? They look real nice too, have you any more pictures? Have you ran it on a car yet. I would be worried about getting a even flow to each cylinder, have you measured this, I dont want a cylinder going lean. Thanks,des.

[Hacke]

Hacke, i was just worried that the angle your wastgate leaves the collector at seems tight. I dont know much about these things, but some of the other "experts" thought the RS unit would be slightly better. But Yours looks much more sexy to me.

Des, having second thoughts

you don´t have to worrie about the WG angle ... the boost dosen´t "run away".. I works on 2 audi s4 at the time and both cars will have over 450hp
they use my header..

if there is anyone who is interessted in costom made headers for more exreme engines, then I can help build one...

I have colect pictures of some of my work...
http://200sx.kicks-***.net/album/alb...nismo&cat=1280

[SteveH]

I have colect pictures of some of my work...
http://200sx.kicks-***.net/album/alb...nismo&cat=1280

Fantastic looking work..Should be sitting in a sculpture exhibition

[diesel des]

Hacke, what about those inlet manifolds. they look very good also. Do you make those? How much £££ ? Thanks,des. Wishing i had a tig welder and time to learn how to steer it right....

[Hacke]

Hacke, what about those .inlet manifolds they look very good also. Do you make those? How much £££ ? Thanks,des. Wishing i had a tig welder and time to learn how to steer it right....

yes i can make inlet manifolds to.. it will cost you 505£ that inkludes shipping.. if you send me your orginal inlet manifold...
then when you gets it, it will look like this -->http://200sx.kicks-***.net/miss_nism...637ee2dfc4.jpg


/ Hacke

[euro-audi-parts]

How would we be able to contact you for the intake manifolds? Also what turn around time are we looking at? I have been struggling to find just the right manifold (that isn't $1700USD) for my project which is near complete, 400bhp '90 90q20v AAN. Price in Euro, USD?

Thank you!

[Stick Insect]

I would have thought the 7A inlet manifold could be used as all I think Hacke needs is the inlet tracts to weld the new plenum chamber onto.

I could be wrong.

There is a huge amount of work to fabricate new inlet runners.

David