Time for some love: 1993 URS4 Avant

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • yaz321
    S2Forum Buff
    • Feb 2020
    • 32
    • Country: England

    #16
    A lot of the underside had naturally seen better days






    Generally speaking, the various layers of protection and thick rubberised factory underseal had done their job very well and had only really been compromised in areas of the floor where there was clearly a lot of salt and moisture thrown up and onto over the years.


    Sent from my iPhone using Tapatalk

    Comment

    • yaz321
      S2Forum Buff
      • Feb 2020
      • 32
      • Country: England

      #17
      The first proper de-rusting job I tackled was the fuel tank, attacking it with angle grinder and various attachments. Make sure it's bone dry and you're in a well ventilated area if not outside.

      I focussed largely on and around the seam as well as anywhere else where there was surface rust visible.



      Gave it 2 coats of BH Hydrate to begin with but admittedly I probably put them on a bit too thick. The product does mention avoiding excess application.



      After BH Hydrate



      Then I went in with BH Electrox.

      A couple of things I found with this product in aerosol form. Firstly, and I know this may sound obvious but make sure you shake the can as per the instructions. Secondly, go in short bursts when spraying. I got a bit carried away, given the size of the tank and found that the product started to splutter everywhere at times.

      Also, in the heavily pitted areas of the tank - particularly around the seam - an angle grinder has its limitations in terms of rust removal. I believe BH Hydrate wasn't able to penetrate some of the heavier pitting. Given I didn't top coat the tank for a few days, when I returned to prep, some rust creep was visible.




      I went back in with the grinder around all of the seam and any of the areas of heavy pitting. I used an alternative product from Buzzweld, called Rust Encapsulator. It comes highly recommended in the Land Rover and MX-5 forums as a first barrier to rust. Not sure how much of it is marketing but time will tell.

      2 coats of BH Epoxy to finish the tank off.




      Sent from my iPhone using Tapatalk

      Comment

      • yaz321
        S2Forum Buff
        • Feb 2020
        • 32
        • Country: England

        #18
        I then moved onto the floor and arches.

        Given this was my first DIY clean-up or whatever you want to call it, I didn't really know how dirty and awkward it can be holding an angle grinder close to your head whilst spitting out 30+ years of dirt and iron oxide.

        My strategy was to work in sections. I started with an arch at a time, and then various sections of the floor, de-rusting and going in with the first coats of Buzzweld RE. This then gave me the flexibility to leave the car for a couple of weeks at a time if necessary without having to come back and remove any surface rust that may have formed.









        There are many nooks and crannies under the car so a lot of patience is required to get down to bare metal. I found the straight shank twist knot end brush drill attachments worked well cutting through stubborn in awkward areas.






        I was able to secure a used, spare wheel well so I went ahead and removed my old one to enable easier access to the inside faces of the rear floor sections.









        Sent from my iPhone using Tapatalk

        Comment

        • Tractor Dave
          S2Forum Zealot
          • Dec 2017
          • 6015
          • Country: Wales

          #19
          Nice progress. It's not much fun doing this job but well worth the end result.
          Nothelle S2 Avant
          Black Ur project
          Silver Rs2 Project gone
          Ocianic Ur project gone
          S2 Coupe project gone
          Urs6 plus project gone

          Comment

          • GT500
            S2Forum Fiend
            • Jun 2006
            • 2181
            • Country: United Kingdom

            #20
            Good work! Just caught it in time. Impressed not gone through. Hard dirty job. The tanks are such an odd shape. I can make one in aluminium but it'll take ages. Every time I look at the spare wheel that never gets used I think it would be easy to make a tank to replace the well and carry a can of goo.
            Rob..
            94 RS2 Noggy,LHD,MTM map,18"cup 1s,245/35/18,Bilsteins,RS2 H&Rs,Cup splitter.
            87 UR 20v ABY
            97 S6 Avant
            96 A6 C4 2.5 TDI quattro avant,Ming,Wietec/eibach,chipped
            1967 Ford Mustang,Eleanor,460ci v8

            Comment

            • GT500
              S2Forum Fiend
              • Jun 2006
              • 2181
              • Country: United Kingdom

              #21
              Diff output seals are impossible to find. So I've found. I tried asking Corteco how many would a batch be but they just ignored the emails.
              let us know if you find some!
              Rob..
              94 RS2 Noggy,LHD,MTM map,18"cup 1s,245/35/18,Bilsteins,RS2 H&Rs,Cup splitter.
              87 UR 20v ABY
              97 S6 Avant
              96 A6 C4 2.5 TDI quattro avant,Ming,Wietec/eibach,chipped
              1967 Ford Mustang,Eleanor,460ci v8

              Comment

              • yaz321
                S2Forum Buff
                • Feb 2020
                • 32
                • Country: England

                #22
                Originally posted by Tractor Dave
                Nice progress. It's not much fun doing this job but well worth the end result.
                Cheers Dave, and thanks for your help along the way - much appreciated.

                Comment

                • yaz321
                  S2Forum Buff
                  • Feb 2020
                  • 32
                  • Country: England

                  #23
                  Originally posted by GT500
                  Good work! Just caught it in time. Impressed not gone through. Hard dirty job. The tanks are such an odd shape. I can make one in aluminium but it'll take ages. Every time I look at the spare wheel that never gets used I think it would be easy to make a tank to replace the well and carry a can of goo.
                  Thanks, and on the the fuel tank there's more to come...

                  Given the tanks in these cars are either leaking or not far from it, I think there'd be a market for a well-developed and tested tank alternative. I've seen mention on the facebook groups of the plastic ones but not sure how obtainable they are and whether they fit without headache.

                  I did consider buying a sheet of steel and riveting it in when I couldn't find a replacement tub but luckily I managed to. Long range fuel tank would be a great idea!



                  Comment

                  • yaz321
                    S2Forum Buff
                    • Feb 2020
                    • 32
                    • Country: England

                    #24
                    Originally posted by GT500
                    Diff output seals are impossible to find. So I've found. I tried asking Corteco how many would a batch be but they just ignored the emails.
                    let us know if you find some!
                    Ok so from what I found, the S4 and S6 have different left-hand side (LHS) rear diff output seals. Both seem to use identical part numbers for the right-hand side (RHS), all listed below.

                    Both S4 seals are readily available. I bought my Corteco parts from Autodoc almost two years ago now but even still, they're currently showing as available.

                    Tradition did have the S6 LHS seal available a couple of years back but they're out of stock at the moment.
                    Given Corteco seem to have put the S4 LHS seal back in production (as listed on tradition "genuine new produced part") it might be worth following up with tradition if you're not getting anywhere with Corteco.


                    S4

                    LHS
                    VAG 017525400 A
                    Corteco 01020537B

                    RHS
                    VAG 016409399 B
                    Corteco 12017270B
                    ----------------------------------------

                    S6

                    LHS
                    VAG 017525400 C
                    Corteco 01034693B

                    RHS
                    (as above)

                    Comment

                    • yaz321
                      S2Forum Buff
                      • Feb 2020
                      • 32
                      • Country: England

                      #25
                      Timely mention of diffs and seals as whilst the rust encapsulator was curing I moved onto taking care of the diff.

                      Drained the oil



                      The flanges come out very easily, one long bolt on each side and they should slide straight out. I torqued the bolts back up to 10NM + 90deg once the seals were changed.





                      Some new plugs (x3), torqued to 25 NM + a dab of red RTV (thanks Dave)



                      Measuring seal depth for the smaller seal as the new one needs to be inserted to same depth manually - there's no stop here.



                      I didn't have a seal puller so I carefully inserted a screw into the seal which did the job well.



                      New seal in




                      Repeat on the other side (no need to measure seal depth here, press home)






                      And then a fill up with fresh fluid



                      I went with Fuchs Titan Sintopoid 75W-90, GL-5. 2L will fill the diff and leave you some left over.


                      Sent from my iPhone using Tapatalk

                      Comment

                      • GT500
                        S2Forum Fiend
                        • Jun 2006
                        • 2181
                        • Country: United Kingdom

                        #26
                        The left one, I've had the tell me its back in stock on tradition for over 18 months. Same on Autodoc. Hopefully they'll come available. It weeps a tiny amount.
                        I changed all the bearings when I did mine. It's going to get some pain in future!
                        Rob..
                        94 RS2 Noggy,LHD,MTM map,18"cup 1s,245/35/18,Bilsteins,RS2 H&Rs,Cup splitter.
                        87 UR 20v ABY
                        97 S6 Avant
                        96 A6 C4 2.5 TDI quattro avant,Ming,Wietec/eibach,chipped
                        1967 Ford Mustang,Eleanor,460ci v8

                        Comment

                        • yaz321
                          S2Forum Buff
                          • Feb 2020
                          • 32
                          • Country: England

                          #27
                          Updates on the way.

                          Back to the floor and arches. 2 coats of BH Electrox followed by seam sealer











                          2 coats of BH Epoxy Mastic next







                          As I was pretty happy with Buzzweld and their rust encapsulator I bought some WAR Underseal to finish off the arches and high traffic bits of the floor.


                          Sent from my iPhone using Tapatalk

                          Comment

                          • yaz321
                            S2Forum Buff
                            • Feb 2020
                            • 32
                            • Country: England

                            #28
                            At this point after long last I was quite happy to begin the re-assembly process. Parts had also come back from powder coating (2 stage, zinc prime + top coat).

                            I started off these rear diff front-support carrier bushes that I got from tradition. They were irrationally hard to get in by hand as per the manual, even with grease. Squeezed them in with some pliers eventually.



                            Then I made up some brake lines and cleaned up the rear t-valve. The measurements listed on etka/7zap for the 3 x brake line lengths are all correct in case anyone was wondering.







                            Sent from my iPhone using Tapatalk

                            Comment

                            • yaz321
                              S2Forum Buff
                              • Feb 2020
                              • 32
                              • Country: England

                              #29
                              I was now ready to get the fuel tank bank in complete with new hose



                              It went back in the car, new genuine nuts all around and the powder coated corner pieces holding it in place. I refilled the tank with about 10L that I had drained out before starting the work.





                              I left the car to sit for a few weeks before getting back to it, but when I did I noticed some bubbling under the epoxy around the left hand front edge of the tank. It was leaking.




                              So I had to get the tank back out and inspect




                              I'd completely missed the pin holes when tidying the tank up prior.

                              I went for the PC-7 epoxy to seal the above pinholes and the Rustbusters Large Slosh kit which coats and seals the inside of the tank.
                              It's a great kit with plenty of instruction but be mindful that you need space and patience in abundance as you'll find yourself tipping and spinning your fuel tank in all sorts of ways! This is also a warm weather activity ideally.







                              The tank was now complete and ready to go back in the car. Once in, I put enough fuel in to essentially submerge the leaking seam and left it for another couple of weeks. With no leaks I was ready to continue


                              Sent from my iPhone using Tapatalk

                              Comment

                              • yaz321
                                S2Forum Buff
                                • Feb 2020
                                • 32
                                • Country: England

                                #30
                                Next up, getting the diff and subframe/cross-brace back in, featuring a Verkline diff mounting bush






                                I generally picked up new genuine nuts and bolts where they were available and only refurbished what wasn't.

                                I went with Verkline solid mounts and used the deep (10mm?) socket trick to centre the subframe before tightening the nuts (45Nm).





                                I had a full set of bushes for the rear trailing arms from Igor (Molnar Igor on Facebook) that I had bought back in 2020 when I first picked the car up. They're yellow polyurethane replicas of the OEM bushes. I was happy with the quality and fitment although I had to push them all in with a bench vice which was tough work.






                                I went with Bilstein B8s paired with Eibach springs. For control Arms I found a TRW left rear which must've been one of the last ones in stock at Autodoc and then an ABS rear right. Will be interesting to see how they fare




                                Sent from my iPhone using Tapatalk

                                Comment

                                Working...