My Project Progress

[Doug_RS2]

Looks really nice there Habib

I was going to ask you where the MAF was since you have a filter right on the end of your turbo but you are running a MOTEC aren't you?

What power is it putting out? How is it running?

[Habib]

last one

[Habib]

Its all running good.

Just got back yesterday from santapod. got a 1/4 mile time 12.443 seconds which is not bad when u got a spare wheel in the boot and a full loaded interior.

[Habib]

power is approx somewhere between 430-460bhp at crank 1.8bar boost

[Doug_RS2]

Sounds good - what turbo are you using? When does the turbo kick in?

Are you happy with that or do you want more yet?

[Habib]

turbo comes kicks in at 3800 and 4200-4500 it really pulls hard.

Im happy with the power my next and hopefully last step would be to change the cams.

the turbo is a KKK 28/29 oil cooled

[Greg_S]

Cool, looking good mate. We were talking about you today wondering on how your project was progressing.

Greg

[jogi730]

Looks really nice there Habib

I was going to ask you where the MAF was since you have a filter right on the end of your turbo but you are running a MOTEC aren't you?

What power is it putting out? How is it running?

Nice looking car Habib. Where in west London are you m8. I'm in Ealing.
If not running Motec what are you running?
Chris

[Habib]

Nice looking car Habib. Where in west London are you m8. I'm in Ealing.
If not running Motec what are you running?
Chris

Im running MoTeC. Im in Hayes not very far from you.

[Robatron]

Im running MoTeC. Im in Hayes not very far from you.

I was in hayes about one hour ago.

and I live in isleworth/osterly, right near ealing.

[Jeffer]

Looks great Habib,

Can you tell me more about your radiator. I'm looking for one of those. And whats your exhaust setup? single damper? and whats the sound like. I ask this because I'm now making a 3,5" turbo back system with side exit like yours. And I have one damper about 40 cm long.

thanks

[S2central.net]

Habib - hey serious progress there. These things always take longer and cost more than you can believe.

Is that the alloy radiator from Dialynx ?

Out of interest, who mapped the MOTEC for you - was it the guys nr Dialynx who are UK agents or somewhere else entirely. Did you wire it yourself or have them do it ?

Any other engine sensor changes required for MOTEC ?

Dare you tell us how much the MOTEC installation and mapping cost you ?

I love the way MOTEC works without a MAF - its one complicated, sensitive, expensive air restricting device that you really don't need !

Paul

[jogi730]

I was in hayes about one hour ago.

and I live in isleworth/osterly, right near ealing.

Hello neighbours Habib and Robatron)!
I really do hope to get my car back for this Saturday.... AMybe we could arrange to meet somewhere soon? Any more from ariound here?
Chris

[Habib]

Looks great Habib,

Can you tell me more about your radiator. I'm looking for one of those. And whats your exhaust setup? single damper? and whats the sound like. I ask this because I'm now making a 3,5" turbo back system with side exit like yours. And I have one damper about 40 cm long.

thanks

The radiator is from Dialynx.
My exhaust system is a 3" from turbo back with one silencer which is about 40cm long. It sounds a bit like the scoobies (Subaru Impreza). It has the low burble tone.

[Habib]

Habib - hey serious progress there. These things always take longer and cost more than you can believe.

Is that the alloy radiator from Dialynx ?

Out of interest, who mapped the MOTEC for you - was it the guys nr Dialynx who are UK agents or somewhere else entirely. Did you wire it yourself or have them do it ?

Any other engine sensor changes required for MOTEC ?

I love the way MOTEC works without a MAF - its one complicated, sensitive, expensive air restricting device that you really don't need !

Paul

Paul - The rad is from Dialynx. I have a MoTeC M48 installed and mapped by Keith at Dialynx which also included the wiring loom etc.

The engine sensors are included in the wiring loom.