looking for set of 4 s2 5x112 pcd hubs

[Jamo]

I never said anything about custom hubs, I was mentioning about custom pcd adapters.

[avants2turbo]

what sort of price would custom hubs set you back? I'd expect around £80 a corner unless you got someone to do a good price for a set?

I've just picked up hubs from an avant so I don't need to do anything like this, just got to fit them now.



Last time I saw they was around £80 each.

I never said anything about custom hubs, I was mentioning about custom pcd adapters.

you didnt, but Acidburn did..

[Error404]

redrill some CQ hubs as mentioned earlier, IIRC they are a larger diameter than the S2 hubs

[avants2turbo]

will CQ hubs fit streight on? and im sure this is a silly question, but what models can i get these from, or can i buy new ones, any idea of price?

can anyone confirm if they are larger?

[Jamo]

On the rears it wouldn't, different bearing size AFAIK on the Avants

[Jamo]

Hold on a sec, this is a reposted thread with the exact same question and Jas11n gave you a link to PCD adapters.

http://www.s2forum.com/forum/showthread.php?t=32453

http://www.concept-wheels.be/wheel-a...-5x120-2-2.htm

[rs2coupe]

Another option you could think about is try swapping 5x114 centers for 5x112 centers on those BBS LM 2pc rims

[avants2turbo]

Another option you could think about is try swapping 5x114 centers for 5x112 centers on those BBS LM 2pc rims

that sounds like a very expensive option...

[Prophet_dlx]

If you can find a shop able to remove 20mm of the hub of the wheel (hope it's the right word for the counterpart of the hub), which means adding 20 mm to ET there would be space for the adapters, it would still fit perfectly and it should be way less expensive.

[avants2turbo]

If you can find a shop able to remove 20mm of the hub of the wheel (hope it's the right word for the counterpart of the hub), which means adding 20 mm to ET there would be space for the adapters, it would still fit perfectly and it should be way less expensive.

removing 20mm off the rear seating face of a wheel sounds really dodgy practice to me! the part of the wheel that the bolt goes through cant be any more than 20-25mm and if you take away 20mm the wheel will just fail

[Prophet_dlx]

they are machined to a pattern and ET at the factory too or do you really think they make a new casting mould for every pattern.
but haven't done it, so I have to admit there could be problems

[Skull]

redrill the wheels to 5x112? there are a lot of wheel with double bolt patterns...

[avants2turbo]

redrill the wheels to 5x112? there are a lot of wheel with double bolt patterns...

have you seen the BBS LM? it would ruin it to have another 5 wholes drilled into it..

[Puglife]

Theres alot to consider here..... and an important point I may make....

The PCD is one problem, getting the hub drilled, wheels drilled etc are all options but still problematic, they link into next point....

Brake discs will have to be custom drilled which your talking yet more expense....

The centre bore of your wheels may not be suitable for S2 hubs, you may have to bore it out to suit or it may already be too large in which case you need to adapt the s2hub to make that a good fit.

If the wheels are worth the retail price given (I know the cost of BBS split rims from my VW days) then why not sell on and get a set that actually fit the car???? I've seen plenty of impeccable sets in 5x112 go for £1500 mark.

[Prophet_dlx]

Way To Easy