Launch Contol switch to the VEMS PNP

[marcusaudi20v]

Hello,
how do I connect to the VEMS PNP Audi S2 for a switch at the Launch Control?

I have a female connector with SSC6 on my VEMS PNP
-Pin1 mcp3208 pin6, CH5 analog input
-Pin2 mcp3208 pin7, CH6 analog input
-Pin3 mcp3208 pin8, CH7 analog input
-Pin4 EC36 pin 34 (power out)
-Pin5 EC36 pin 36 (power out)
-Pin6-GND

In the VEMS manual is only so PIN16 of EC18 to EC36 Pin28 with a resistance to the switch 2K7

Help me please Huh

[pnanassy]

Hello,
how do I connect to the VEMS PNP Audi S2 for a switch at the Launch Control?

I have a female connector with SSC6 on my VEMS PNP
-Pin1 mcp3208 pin6, CH5 analog input
-Pin2 mcp3208 pin7, CH6 analog input
-Pin3 mcp3208 pin8, CH7 analog input
-Pin4 EC36 pin 34 (power out)
-Pin5 EC36 pin 36 (power out)
-Pin6-GND

In the VEMS manual is only so PIN16 of EC18 to EC36 Pin28 with a resistance to the switch 2K7

Help me please Huh

Switch to ground with a press button any of pin 1,2 or 3.
Then you need to configure the input as Launch.Is this 1.1.27 or 1.1.57?
Go to Launch menu and select input channel (CHX) which you have wired.
If everything works fine you will see a status light lighting up on the main screen.

HTH ,Peter

[marcusaudi20v]

Switch to ground with a press button any of pin 1,2 or 3.
Then you need to configure the input as Launch.Is this 1.1.27 or 1.1.57?
Go to Launch menu and select input channel (CHX) which you have wired.
If everything works fine you will see a status light lighting up on the main screen.

HTH ,Peter

Hello,
yes I still use the 1.1.27.
In 1.1.57 I have the problem so that map is max 255Kpa :-(
When i connect the switch to Pin3 at the SSC6.Which channel do I need to because in Megatune choose?
Ch 7?What is that?
I upload a Picture from the Options.


Thanks

[a4kquattro]

select "7" from that menu.

your map would only be limited to 255kpa if your ecu came with a 2.5 bar map (this is not normally the case) or you have selected the wrong profile. You should be running the "high boost" profile for the 400kpa map sensor..

[marcusaudi20v]

Hello,
ok i tested with Ch7 and post my results.
No, my VEMS PNP have the 500kPa sensor.
With 1.1.27 everything works with High Boost and 500kPa sensor.
The VEMSTUNE have a software bug, and shows instead 500kPa only 250kPa.Also exactly all the load points are middle.Ist a bug in the software allegedly

[max_s2]

IIRC, you must set to high-boost to have 3Bar maps.

[A80Avant]

no it still doesnt work that way. although if you set it on high boost it actually reads properly the graphs dont change to take you up to 500kpa but they still read 255. I have talked to marcell about this and they are working on it. For the time being you just have to judge by middle points.255=500 and 124=250kpa and so forth...

[max_s2]

Hmm. I've set high-boost and my maps are up to 3bar (1.1.53 fw)

[Jamo]

Hello,
ok i tested with Ch7 and post my results.
No, my VEMS PNP have the 500kPa sensor.
With 1.1.27 everything works with High Boost and 500kPa sensor.
The VEMSTUNE have a software bug, and shows instead 500kPa only 250kPa.Also exactly all the load points are middle.Ist a bug in the software allegedly

Has this been corrected and your running 1.1.57 or did you stick with 1.1.27?