Whats the part number please? 3b Front Caliper Carrier Mounting Bolts?!

[s2dude]

ok guys//
I cant get access to my etka at the minute so I need some help with a few part numbers please.....cos Ive got to order these bits ASAP////

1991 3B S2

Front Brake Caliper Carrier Mounting Bolts? PN Please?!!

Also, the PN for the pin slide assembly kit please (pin with rubber boot on the outside)

THANKS

[S2 Ant]

321 615 141 - M8x21 i believe these are what you need, Caliper to carrier bolts
N 907 085 02 M12x1.5 - Carrier mounting bolts.

I cant see the pin slide kit you refer to tho

[Audi Parts Guru]

Also, the PN for the pin slide assembly kit please (pin with rubber boot on the outside)

Think you'll find it's 443 698 470. This kit already contains the bolts 321 615 141

[BRY]

Not the little sliding pin bolts - the big bolts for the carrier to hub which are rounded on his car.
M12x1.5 is the thread as they are the same thread as the RS2 bolts.

I think you should stop wasting your time / money and get some proper stoppers

BTW Thanx for the disc - straight in last night no problems, key was included.

[s2dude]

Not the little sliding pin bolts - the big bolts for the carrier to hub which are rounded on his car.
M12x1.5 is the thread as they are the same thread as the RS2 bolts.

I think you should stop wasting your time / money and get some proper stoppers

BTW Thanx for the disc - straight in last night no problems, key was included.

Thanks for all part numbers guys
Except Im a bit confuddles now?!
i should have exlpained a bit better...

As BRY says the caliper mounting bolts (the main ones) are sadly rounded by some numpty

So Im going to have to cut them off and use new ones (major PITA) so I need PNs so I can get 4 of those please....

and also I decided as Im going to be waiting for those I may as well get new slider kit (with the rubber boot) as one side is a bit sticky...and well....Im a fussy SOB!!!

So far I have

N 907 085 02 M12x1 - Carrier mounting bolts. (bry thinks M12x1.5???!)

and 443 698 470 (slider thingy kit)

Can someone confirm this before I order. TIA

Also BRY//

NO problems re the disk mate...glad the key was on there
I forgot about that bit as Ive not used it for a few weeks.

Im seriously thinking about getting the proper stoppers at the mo just buying a hosue though is a bit of a burden on the wallet tho...
Are ALL bits in stock then if I knacker the brakets by any chance cutting the bolts out (or if I lose it and cut them off )

nb// Got to the top bolt out of each side.....bottom is a non starter...and the metric size down slips too
Gonna be a fun Saturday AM!!!

[S2 Ant]

Ah yes, you are correct, i misread the screen, they are indeed M12x1.5x35
Ive corrected my previous post as well

[s2avant]

and also I decided as Im going to be waiting for those I may as well get new slider kit (with the rubber boot) as one side is a bit sticky...and well....Im a fussy SOB!!!

and 443 698 470 (slider thingy kit)

This kit does NOT include the slide pin itself. All you get is the boots, grease and new bolts. The only way to get slide pins is to order new carriers. If you get the kit you will need to strip the carrier and clean up the pins you then have to regrease and fit it back together with the new boots.

The bolts for the carrier are indeed N 907 085 02 and if you run down to your local dealer they will be able to get them for tomorrow morning for you. Seriously, you will have to run...you've got 43 mins before VOR cutoff.:mischeif:

Ben

[s2dude]

This kit does NOT include the slide pin itself. All you get is the boots, grease and new bolts. The only way to get slide pins is to order new carriers. If you get the kit you will need to strip the carrier and clean up the pins you then have to regrease and fit it back together with the new boots.

The bolts for the carrier are indeed N 907 085 02 and if you run down to your local dealer they will be able to get them for tomorrow morning for you. Seriously, you will have to run...you've got 43 mins before VOR cutoff.:mischeif:

Ben

Hehe

Thanks mate....
I didnt realise they came without pins but its the boots I need so I will polish the current pins up and rebuild

and I made it to the local dealer thanks
did it by phone cos they know me by know and I dont have to pay till collect
gotta get them in the am....