Headgasket for 82.5mm bore?

**terrybullwon** · 2 April 2008, 08:29

I can bore you out a standard one to 83mm

**Flat on my back** · 2 April 2008, 09:06

.

and mine...

**terrybullwon** · 2 April 2008, 09:57

Originally posted by Flat on my back

and mine...

Best drop me a PM

**Floddy** · 2 April 2008, 16:41

Thanks for the offer!

How does boring out the gasket work? I don't remember by myself, but someone said that the layers were attached to each other in some way, right at the edge of the cyl. holes?

**terrybullwon** · 2 April 2008, 17:23

I use a torque plate to compress the head gasket. And then bore it out.

If you would like one just say...

Torque plate

**Floddy** · 2 April 2008, 17:35

Ah, I think I've seen something like that before.

How many have been running with modified headgaskets?

**terrybullwon** · 2 April 2008, 18:35

Originally posted by Floddy

Ah, I think I've seen something like that before.

How many have been running with modified headgaskets?

I have not used one yet, but will be using one with my JE's and over 2bar boost. Faheemo and an American member on this forum are doing the exact same thing

I spoke to a head gasket specialist and he suggested that this maybe the best way for me to achieve what i wanted to do.

**Faheemo** · 2 April 2008, 21:10

I Second that !
Ive searched high and low for an alternative big bore gasket.

My bored gasket is on- just doing the manifold and plumbing and will be firing her up soon.

**terrybullwon** · 2 April 2008, 21:25

Originally posted by Faheemo

My bored gasket is on- just doing the manifold and plumbing and will be firing her up soon.

Your ahead of me, keep us updated.... Very excited about this

**fasterthenrs2** · 3 April 2008, 03:03

So far I have 10K on mine 83mm hg, boost levels up to 35 psi and I did make extra one if any interest PM me

Brandons 1990 10sec CQ20VT

http://www.motorgeek.com/phpBB2/viewtopic.php?t=16745

Crow got sold to Brandon, and he decided to keep original tread going, that said Crows new live starts on a page 107, Good luck to Brandon and 9 no bust :-) Heh there it goes, car started out with AAN engine IA Stage 5 software, gt2871 turbo and rs2 replica injectors, MAF all custom fuel...

**Floddy** · 3 April 2008, 05:56

Originally posted by fasterthenrs2

So far I have 10K on mine 83mm hg, boost levels up to 35 psi and I did make extra one if any interest PM me
http://www.motorgeek.com/phpBB2/viewtopic.php?t=16745

Did you also modify a RS2 one?

**fasterthenrs2** · 3 April 2008, 11:07

No it vas AAN ML HG I did use junk 7A blok and decking plate to slightly snag gasket down, I think I did cut like .5mm of

**terrybullwon** · 3 April 2008, 15:14

Originally posted by fasterthenrs2

I think I did cut like .5mm of

Think? how did you do it? with a file

**Faheemo** · 3 April 2008, 18:07

Originally posted by fasterthenrs2

So far I have 10K on mine 83mm hg, boost levels up to 35 psi and I did make extra one if any interest PM me
http://www.motorgeek.com/phpBB2/viewtopic.php?t=16745

2.3 bar boost on 3071

Headgasket for 82.5mm bore?

Headgasket for 82.5mm bore?

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment