00561 and low boost

[AndyP]

When you changed the injector, did you just change the one that was faulty? I'd always fit injectors as a flow matched set.

[twoqu]

Another variable is the Vmap! Are you 100% on the jumper settings for the S/W.

[dobbin]

boost leak test on rs2

i had similar problem running rich and boost leaks, prj told me to pressure check inlet manifold and pipes
to back of manifold and to fpr found 3 small leaks using soap spraying from a bottle after 1bar pressure its the best way to find small leaks , also check turbo hoses again using the same method.

[A80Avant]

good checks all of the above, however, im with those that say boost leaks, and also check for any vaccum hoses that may have gone, clean the MAF if dirty, check the ISV hoses as they tend to go and create a boost leak.

from memory, lamda would also come up if lamda was at fault as well, but i may be mistaken.

[prj]

Running lean due to a faulty injector?
Have you measured compression? Are you sure one cylinder is not gone?

[UrS4boy]

This might be another case of the R201 resistor!
Are you using RS2 S/W in a ABY ecu without a change in the resistor?

LOL. Not likely the cause, even if true.

[twoqu]

This might be another case of the R201 resistor!
Are you using RS2 S/W in a ABY ecu without a change in the resistor?

[UrS4boy]

Yea I seen your post and though I would replace the FPR to see if that helped but no change. It was the (mul) not reached I was getting

Don't scratch your head, re-read my post and look for boost leaks (despite what the smoke test indicated, you likely have a split hose that only opens under boost, say 1 Bar, pressure).

[sjw185]

Mine was fuel pressure giving 561.

Hth

Yea I seen your post and though I would replace the FPR to see if that helped but no change.
It was the (mul) not reached I was getting

1 Fault Found
00561 - Mixture Adaptation
13-00 - Adaptation Limit (Mul) Not Reached

[GT500]

Mine was fuel pressure giving 561.

Hth

[UrS4boy]

Just to be clear, the meaning of the 00561 code

2413 (Blink Fault Code), 00561 VAG1551/2 Fault Code Number
Mixture Adjustment,
Adaptation limit exceeded, Adaptation limit not reached, Leakage in exhaust system before 3 Way catalytic converters, Incorrect signal for Mass Air Flow Sensor, Spark plugs, ignition coil(s), or Ignition Coil Power output stage malfunctioning
Symptom: Rich mixture, increased fuel consumption

**********

Typically this occurs when there is a boost leak after the turbo and before the engine. Less air shows up at the intake than the ECU had expected so there is too much fuel injected into the cylinders. Via the O2 lambda sensor, the ECU tries to adjust the fuel down but the air leak is too much and it can not adjust the fuel down enough. Solution = find and fix boost leak.

Other potential issues = MAF sensor and O2 sensor.

Good luck

[sjw185]

Having a issue with low boost and sometimes get the 00561 code.
Not been working with the S2 for a long time so decided to get it on the rollers to check fueling etc as the last time it was on the Dyno it was running lean due to a faulty injector.

With injector replaced, new HRC 255 fuel pump and FPR
Figures looked good apart from seeing only 1bar of boost.
Talked about the fault code and checked voltage on Lambda while at idle and it was showing .05 - .75v
Have a new Lambda to fit but even with the fault cleared I cannot get full boost and feel it is something like a sensor holding it back?

Garage also did a boost leak check using smoke to check for leaks.
They suggested as the fault code did not appear on the power run that possibly the waste gate spring is to fault for the low boost?

Checks Ive carried out prevously

Boost leak check at 1bar
Checked hose in ecu to VmapD
checked alt sensor in vagcom
unplugged MFTS
checked plugs
checked waste gate seal
Checked throttle Pot

Checks to do

Replace Lambda
Unplug WGFV to check I get 0.4bar

Any thoughs or suggestions

Cheers

Steve

Dyno report (power at wheels)