Wiring loom for Reverse Mount IM

[Lupo911]

Here you go Carsten, it's slightly off topic so was gonna contact you privately. Rest of the kit is great, could do with a 50mm hose joiner and this loom to complete a full plug and play kit :-)

The hose in black below needs around 25 mm longer on the longitudinal where it goes over the ic to tb hose, and 50 to 60 mm longer on the transverse to the aux radiator. It can be stretched to fit but it rubs on the throttle dampener.

oh, i wasnt following on that...

something is wrong on your side... it should look like that.

[mastermind]

Did you just cut the cable and extend the tps?

Yes, that's what we did.

[dreft]

We made up our own extensions for the wiring and didnt have any issues. Here is a pic.

Did you just cut the cable and extend the tps?

[S2central.net]

need to dig up this one again... seem to recall that the 6-pin MALE is PCB mounting only... but I would be delighted to be proved wrong.

[spink]

Found it in the old Bosch paper catalog

6-pin MALE = 2 227 000 104 - there is a question whether supplied pins are perfect for this but lets see
6-pin FEMALE = 1 287 013 004
2-pin MALE = 1 287 013 002
2-pin FEMALE = 9 122 067 011

All above parts are supposedly kits that include pins and rubber boot. I'll try a couple of Bosch suppliers for prices - anyone else is welcome to try their local sources as well of course.

did you have any joy with this Paul?(prices/sellers?)

[mastermind]

We made up our own extensions for the wiring and didnt have any issues. Here is a pic.

[madpugger]

This is it stretched on...

[madpugger]

Here you go Carsten, it's slightly off topic so was gonna contact you privately. Rest of the kit is great, could do with a 50mm hose joiner and this loom to complete a full plug and play kit :-)

The hose in black below needs around 25 mm longer on the longitudinal where it goes over the ic to tb hose, and 50 to 60 mm longer on the transverse to the aux radiator. It can be stretched to fit but it rubs on the throttle dampener.

[Lupo911]

Ahh ok, that's good info. Somewhat off topic, but did your rad top hose fit? Mine is about 4" short on the top of the aux rad. It's a Wagner hose.

please post a Picture...

[madpugger]

Hmm, did you have the throttle close damper fitted too? My hose wont fit with it fitted

I need to PM you re RS2 trims too

[Jamo]

It fitted before I ditched the aux rad, reminds me I must find and sell it!

[madpugger]

Ahh ok, that's good info. Somewhat off topic, but did your rad top hose fit? Mine is about 4" short on the top of the aux rad. It's a Wagner hose.

[Jamo]

Isv doesn't need extended. Just the tps and iat wires.

Paul, any joy in this? The 6 pin connector that we were struggling to find only has 5 wires. Given how easy they come apart we could swap with a 5 pin male and female if this helps?

I'm really looking for a plug in solution ASAP, would happily send you plenty cash to cover it!

Depends if you have a MK1 or MK2 wagner manifold, with the MK2 you dont, with the MK1 you do if you have the ISV at the front

[madpugger]

You have to extend the throttle body and the ISV. Also check the MAT plug will reach

Isv doesn't need extended. Just the tps and iat wires.

Paul, any joy in this? The 6 pin connector that we were struggling to find only has 5 wires. Given how easy they come apart we could swap with a 5 pin male and female if this helps?

I'm really looking for a plug in solution ASAP, would happily send you plenty cash to cover it!

[giorgioS2]

any news??

I'm interested too!