2.6 V6 PAS Pump tips needed on stripdown

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • catgroom
    S2Forum Enthusiast
    • May 2007
    • 137
    • Country: United Kingdom
    #1

    2.6 V6 PAS Pump tips needed on stripdown

    Hello!

    Im needing to remove and replace a gasket on my PAS pump.Its the 2.6 ABC engine.

    Anyone done one on one of these??

    Hope posting about V6s isnt p***ing anyone off given that this is an S2 forum!

    Steve
    1994 2.6 V6 in LY6G Vanillegelb (Lime Pastel).
    202k,Throttle Body Ported,Stainless.
    Tags: None
    • iain1067
      S2Forum Maniac
      • Mar 2005
      • 984
      • Country: United Kingdom
      #2
      is it leaking from the X ring plug on top??? if so then they are available from audi plus the rubber seal,

      Iain

        Comment

        • catgroom
          S2Forum Enthusiast
          • May 2007
          • 137
          • Country: United Kingdom
          #3
          .

          No Iain,I changed this part very recently using a VAGparts one.

          Its leaking from the gasket between the frontmost piece and the next piece its bolted to.

          Im going to remove and just replace gasket if VAGparts do them.Audi dont.They wont even sell the plug and washer.Pfffff

          Steve
          1994 2.6 V6 in LY6G Vanillegelb (Lime Pastel).
          202k,Throttle Body Ported,Stainless.

            Comment

            • catgroom
              S2Forum Enthusiast
              • May 2007
              • 137
              • Country: United Kingdom
              #4
              .

              New one going on

              Bah!lol!

              Steve
              1994 2.6 V6 in LY6G Vanillegelb (Lime Pastel).
              202k,Throttle Body Ported,Stainless.

                Comment

                • iain1067
                  S2Forum Maniac
                  • Mar 2005
                  • 984
                  • Country: United Kingdom
                  #5
                  just out of interest where did you get the seal from???? and has it solved your leak

                    Comment

                    • catgroom
                      S2Forum Enthusiast
                      • May 2007
                      • 137
                      • Country: United Kingdom
                      #6
                      .

                      Have a guess!!lol!!

                      No,in this case it didnt.Im told its the usual culprit though.Itll go on the replacement pump.

                      Im not too proud to admit that in this case I strongly suspect it was me for over filling it once.I think that due to this it blew a seal.

                      No matter,got one sourced for £25 now thanks to Cullam3n.Nice one Pasc!

                      Steve
                      1994 2.6 V6 in LY6G Vanillegelb (Lime Pastel).
                      202k,Throttle Body Ported,Stainless.

                        Comment

                        Previous template Next
                        Working...

                          We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                          By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                          I Agree