clutch for 650hp 750nm rs2

[brider]

Hello to all.
i have one questtion about clutch - now i have spec 3+ with aluminium flywheel from S6 2.2. And after 3rd run it skid - so i need another clutch. What You can recomend me. now is about 650 hp and 750 nm
but i whant to buy clutch for ~ 700 hp and 800nm. for me its better to buy from USA.
thanks a lot for Your answers.

[Costash]

Southbend all the way stage 4 or 5 !!!

[brider]

So, You think that stage 4 or 5 will good for 800nm?
And whitch is better? Stage 4 or 5?
I ask because on the spec site there is information that stage 4 is for ~400nm and stage 5 for ~450nm...
Do You think stage 4,5 will good?

[repo]

I am quite convinced no single plate will hold 800Nm for long. Even real 700Nm is too much for single plate.

[Costash]

I have stage 4 wich is good for 800Nm.Stock new clutch it is holding 400Nm.(Stage 4 "Extreme-Street" Series:

This kit uses the same pressure plate as the stage 3 kits but with a dual face feramic clutch disc (pressure plate and flywheel side). good for 550+ft/lbs of torque. For even more power handling, consider swapping to a single mass flywheel setup (7a/Coupe Quattro style flywheel). )

[brider]

How many km did You ride on stage 4?

And where i can see/buy dual clutch?

[repo]

http://www.s2forum.com/forum/showthread.php?t=38765

Shoot me an email for details

repo (ät) aprfinland.fi

[Costash]

I have donne 8k km.I am sure it is very good clutch, but you can try whatever you like!I am sure the one Repo sell it is very good too.

[terrybullwon]

I have donne 8k km:

With how many NM/HP?

[brider]

http://www.034motorsport.com/clutche...s-p-18993.html
what You can say about tilton?
who did ride this - which one (i mean there are different kind of torgue capacity) and how many km You did ride on it

[Audi_CQ]

I've been using a SPEC 3+ with a 5+ pressure plate for several years and lot of miles on track days with no problem. 2.5L, 580hp / 700nm @ wheels on Mustang dyno. Never used on drag strip so don't know how good it will hold there.

[Audi_CQ]

http://www.034motorsport.com/clutche...s-p-18993.html
what You can say about tilton?
who did ride this - which one (i mean there are different kind of torgue capacity) and how many km You did ride on it

I used to have a triple plate Tilton(cerametalic), but was useless on the street. A typical on/off clutch that's OK for track use, but nothing else. Maybe the carbon clutches are better for street use, but have never tried one so can't say for sure.

[brider]

but now i use spec 3+ - and after 5000km of not too fast drive - it start skid after 3rd run..((
i have just 570hp on the crank and about 650nm...

what about tilton life time?and what is better for life time - cerametallic or sintered iron?

[brider]

Audi_CQ
i have some questions - could You answer)))
1 whitch flywheel do You use?
2 how many km did You ride (approximately)?
3 whats You style of driving? aggresive?)))
4 and how many bar turbine hold on 580hp?

sorry for many questions - but i whant to understand..))

thanks for Your reply

[Audi_CQ]

Audi_CQ
i have some questions - could You answer)))
1 whitch flywheel do You use?
2 how many km did You ride (approximately)?
3 whats You style of driving? aggresive?)))
4 and how many bar turbine hold on 580hp?

sorry for many questions - but i whant to understand..))

thanks for Your reply

1. 034 60-2 : http://www.034motorsport.com/product...roducts_id=678
2. I'm not sure how many km I've used it, but maybe 30-40' and counting...
3. Daily driver + a lot of track day action (1000+ km on a good season )
4. 580hp @ 1.7bar and 700nm @ 1.8bar on E85.