Zermatt silver urq

[DJones]

Pete, looks great, ride height looks good..

[newsh]

A proper set of Ronal quattro wheels on it! Nice!

[slacky]

Taking shape very nicely,

[andy10v]

Woot!

Much improved ride height

[Error404]

nice, you're keeping the rear steer though right?

[Jonnybravo]

Looks sweet Pete, can't wait to see the finished article.

[Acidburn]

Wiring done? Hmm you sure hehe

Most of it, ask tonk's if you don't believe me....

not the best quality, engine now in, head on, timed up, manifold is off and now with another forum member whilst the new one's ordered, wiring done.....

heads been back off
quattronutters done some work on it
new headgasget set which can still be bought new unlike what people on here say.
new exhaust manifold
change of plans with rocker cover/catch tank setup
change of plans with seat
injectors arrived
intake almost sorted
brakes are being worked on so should be on soon

Pete, looks great, ride height looks good..

cheers but only had half the engine in with that shot, probably be about that or a tadge lower once done....

A proper set of Ronal quattro wheels on it! Nice!

Taking shape very nicely,

Woot!

Much improved ride height

nice, you're keeping the rear steer though right?

Looks sweet Pete, can't wait to see the finished article.

Cheers nearly have everything for it now, only about £100 to spend with tps and a turbo to get.

[Error404]

wootage! Let me know when you wanna get those lines sorted dude

[gavs20v]

Great to see it finally done. Great work pete

[s2driveruk]

Pete - havent seen you about much on here recently (not that i have either...) but good to see that you've been burning the midnight oil on this - great to see a project coming together Will be fantastic once finished

[Acidburn]

Pete - havent seen you about much on here recently (not that i have either...) but good to see that you've been burning the midnight oil on this - great to see a project coming together Will be fantastic once finished

Yes I need to pop up to yours soon, I killed my daily so no transport currently

I've been messing with this today, biggest issue atm is the linkage for the 6 speed. I've tried two different ways already that people have suggested and both don't work so have another idea but still struggling with it.

How hard is it to sort a linkage out that works on this, its basically full s2 running gear but with a 6 speed dsy box, I need to check the top of it compared to a stock box as I think there is a molded nut fitting on the top that might be causing me issue's with the 2nd option I tried on the car that was suggested by will20v.

Once thats done I can start sorting the last bits out as I won't have to keep messing with the subframe/engine mounts.

[Tonks4x4]

Now I have actually done just this on a customers car I can tell you how I did it.

I used a gear linkage cradle from a 100/S4. This needed some steelwork trimming off and then bolted into the standard mounting locations.
I had to drill and bolt an extra mounting location in it.

I then just hacked, chopped, bent and welded one of the S4 selector rods until the cleared everything and were able to select every gear.

The bonus with using the S4 cradle is that it has the reverse gear stop in the correct location.

The interior trim all fits too although it is very very tight fit

[Acidburn]

I did have a urs4 rear setion housing sitting in the car with the s2 front half of the linkage, this didn't work as it was too short to join the two bits together. I did enlarge the holes on the base so it fitted in the car properly and also cut the front off the base section for the urs4 ball section so it would move forward a bit more. Still no joy....

[Acidburn]

Slow progress till christmas is out the way and the post offices/couriers open. Been to see martin tonight and picked up these whilst showing his missus the s2.

[Jonnybravo]

Feeling flush Pete ? lol

Any reason why you chose to go down that route, dry break joints are a bit "motorsport"

Either well, can't fault them for looking good.