Part number request or gaskets

[Christophski]

Hi Guys

Got a standard turbo to fit onto my S2 as my current one is a bit smokey. Does anyone have either the part numbers for both the gaskets I would need or do they actually have decent or useable gaskets they would part with?

The ones I mean are the gaskets that go where you bolt the turbo on. Not actually the internals of the turbo...

Its for an ABY engine.

Cheers
Chris

[Christophski]

After a bit of searching I have found one of them is 447 253 115 (I hope) but im not sure what the other one is or if there is supposed to be one at all.

Any pointers chaps?

[sidrick]

035129589D engine side
447253115 exhaust side

According to vagcat

[Christophski]

Thank you for that. Now only have to hope they arent NLA or mega money hahaha

[UrS4boy]

20VT Exhaust System Diagrams and PNs and more

Hi Guys. Got a standard turbo to fit onto my S2 as my current one is a bit smokey. Does anyone have either the part numbers for both the gaskets I would need or do they actually have decent or useable gaskets they would part with? The ones I mean are the gaskets that go where you bolt the turbo on. Not actually the internals of the turbo...Its for an ABY engine. Cheers Chris

I guess I need to port this Exhaust System post over here so it can end up a sticky.

http://forums.quattroworld.com/s4s6/msgs/196904.phtml

[Christophski]

Coolios, thank you for this. Confirmation of the numbers I need

[macspring]

I guess I need to port this Exhaust System post over here so it can end up a sticky.

http://forums.quattroworld.com/s4s6/msgs/196904.phtml

Dave for Pope !

Nice link, as usual, gives me the nut and bolts sizes to get them in stainless steel.

Ironically just took my 3" inch down pipe and 3" inch exhaust, re-installed RS2 downpipe and S2 exhaust, still with chip k24, car is beautifully quiet again and no slower. Fit is perfect, never should have left it, IMHO.

Went from above to Milltek with RS2 down pipe, and then 3" down pipe and exhaust, all non oem bits were a bad fit and too loud. And now back full circle, and significant funds expended.

IMHO, exhaust mods for ABY / AAN should go no further than Wagner RS2 Exhaust manifold, RS2 down pipe, Ulimot cat by pass pipes and standard good condition exhaust system, if staying below 440 / 500bhp, and wanting easy fit on your driveway, and guaranteed to work with no knock on complications.

Sorry for partial off topic.

[UrS4boy]

Dave for Pope !

Unfortunately, that would be against my religion.

[LHD_Kid]

sent via Tapatalk

[Christophski]

Quick question, from looking at the part diagrams in the link provided above, is there supposed to be a gasket between the wastegate and the manifold? If so whats the PN?

[Rusty]

Get all the oil and water line gaskets and sealing rings too

[Christophski]

Good idea that man!

Im changing the turbo over on my ABY, So from what I can tell I need the following:

2x Gaskets on flexi pipe part of exhaust - 857 253 115 (Rusty is getting these made?)
1x Turbo > down pipe gasket - 447 253 115
1x Engine side gasket - 0351 295 89D

Is the above correct?

With regards to the oil and water line gaskets and sealing rings does anyone have the part numbers I will need and the quantity of each that I will need?

Thanks in advance

[Rusty]

If the EM-turbo-DP gaskets have revently been replaced, then theymay be in good condition, otherwise, yes, get them.

Also worth getting 4 new nuts to hold the turbo on and 4 new studs and nuts for the turbo - DP.

[Christophski]

Yeh, I didnt replace the gaskets when I did previous work, I just used the bits I had. I did however change the studs and nuts as the old ones werent that good lol.

How long until the gaskets from you are ready bud?

When is uncle Dave coming along with the other answers for PN's???
We all know he is our part number god!

[Error404]

I have all of these numbers on my list of stuff to buy a home, but that's not much help to you now mate is it. Here is what I have at work:

Approx price shown too mate.

Turbo to manifold gasket - 035 129 589 D £19.00
turbo to downpipe gasket - 447 253 115 £8.50
Wastegate Flexi gaskets - 857 253 115 x 2 £18.00
Turbo downpipe nuts - N 903 690 01 x 3 £3.00
Turbo downpipe nut - N 900 730 01 x 1 £4.00
Wastegate flexi nuts - N 902 002 01 x 3 £2.00
Downpipe flexi nuts - N 900 850 01 x 3 - £0.50