Knock Sensor Replacement

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SR71
    S2Forum Addict
    • Apr 2004
    • 330
    • Country: Wales

    #1

    Knock Sensor Replacement

    Any chance of a guru posting a knock sensor replacement "how-to"?

    I've got both replacement sensors but only appear to be able to locate one...


    Cheers.
    00 Audi B5 S4 MRC550
    08 RRS TDV6 HSE
    03 Kawasaki B2 ZX12R 1287cc
  • SteveH
    Super Moderator
    • Jul 2003
    • 4460
    • Country: United Kingdom

    #2
    The two sensors are on the same side of the block ( under the inlet manifold) You may need to remove the main radiator to get a good look at them.
    91 Modded 3B
    14 A6 Avant Black Edition

    Comment

    • 4WheelDrifter
      S2Forum Zealot
      • Oct 2004
      • 5773
      • Country: Devon

      #3
      I've done both on my cq20v.
      I just moved P/S pump to get to No.1
      and the fuel pressure regulator to get to No.2
      HTH
      SS

      Comment

      • audiman
        S2Forum Freak
        • Jul 2003
        • 4827
        • Country: United Kingdom

        #4
        I havent ever changed mine, but i have looked at doing it :O

        Doesnt look easy. The one closest to the bulkhead isnt too bad but the front one looks a right nightmare.
        sigpic
        Tom C - www.rcmr.co.uk
        Audi UR Quattro
        Audi 100 C3 2.0 5 cyl 115ps
        Audi S2 - 07k engine project aiming for 800ps
        Audi B5 RS4 645ps 911nm

        Comment

        • 4WheelDrifter
          S2Forum Zealot
          • Oct 2004
          • 5773
          • Country: Devon

          #5
          I haven't done either in my S2, but i'm sure if you move the P/S pump it's right there.
          It's just the usual case of working out what to move to make the job easier.
          SS

          Comment

          • audiman
            S2Forum Freak
            • Jul 2003
            • 4827
            • Country: United Kingdom

            #6
            Cool, good tip, hope it does apply to the S2. Would be a lot easier than removing the rad
            sigpic
            Tom C - www.rcmr.co.uk
            Audi UR Quattro
            Audi 100 C3 2.0 5 cyl 115ps
            Audi S2 - 07k engine project aiming for 800ps
            Audi B5 RS4 645ps 911nm

            Comment

            • 4WheelDrifter
              S2Forum Zealot
              • Oct 2004
              • 5773
              • Country: Devon

              #7
              Yeah. I definitly didn't move the rad.
              I think i discovered this when i replaced the P/S pump mounting bracket. (The old one broke on the way into a sharp corner )
              This was after i struggled around it to fit Knock Sensor 1!
              SS

              Comment

              • Greg_S
                Administrator
                • Jul 2003
                • 12430
                • Country: United Kingdom

                #8
                Yeah the second one nearest the front of the car is a PITA, you need two elbows to get your arm down there normally or take the rad off its mountings and take dip stick out and you can just get to it then.

                Greg
                Greg

                S2Forum.com Administrator & Webmaster

                '93 Coupe with a few tweeks

                Comment

                • nickhey
                  S2Forum Fanatic
                  • Jul 2003
                  • 73
                  • Country: United States

                  #9
                  How much are they? Do VAG-parts sell them?
                  I keep getting a fault code for knock sensor with vag-com.
                  Doesn't seem to knock at all though - maybe the remaining one is working twice as hard ( ha ha )
                  Nick

                  Comment

                  • SR71
                    S2Forum Addict
                    • Apr 2004
                    • 330
                    • Country: Wales

                    #10
                    Originally posted by nickhey
                    How much are they? Do VAG-parts sell them?
                    I keep getting a fault code for knock sensor with vag-com.
                    Doesn't seem to knock at all though - maybe the remaining one is working twice as hard ( ha ha )
                    Nick
                    Part numbers are:

                    054 905 377G
                    054 905 377A

                    Both £25.66 each from VAG Parts.

                    Cheers guys...

                    Looks like another 6 hour job then.

                    00 Audi B5 S4 MRC550
                    08 RRS TDV6 HSE
                    03 Kawasaki B2 ZX12R 1287cc

                    Comment

                    Working...