URS6 Auto

[shaun5]

[QUOTE=UrS4boy;834624]Thanks. I know what the blue and silver 4HP-18 tag is all about. However, I don't know what this A 100 tag means. Where is it located?

I will take another picture from further away and discribe where it is

[spink]

Picture for Spink

Total length is 2 foot.

I will have a look in about an hour

By the way,I spray the tanks with a schutz type stuff

[spink]

49"


(2wd c4 rear)

[shaun5]

[QUOTE=shaun5;834654]

Thanks. I know what the blue and silver 4HP-18 tag is all about. However, I don't know what this A 100 tag means. Where is it located?

I will take another picture from further away and discribe where it is

picture of where the plate is located

[shaun5]

49"


(2wd c4 rear)

opps, mine are 49" (4 foot, not 2 )

Im still deciding what im gunna do about the sensors, yours would do but haven't got all the mounting lugs points

[shaun5]

Didn't do much to the car yesterday, i collected some parts from the S4 to fit to the S6.

Handbrake lever has got no free travel now so only comes up a little, like it should

[shaun5]

front inner wings have been rubbed down, rust treated and under sealed

The lip on the front wings were a bit rusty so i rubbed them down and treated.

[UrS4boy]

[QUOTE=shaun5;835034]

picture of where the plate is located

Okay. Thanks. I guess I am *NOW* confused as to the location of this one:

[shaun5]

There are 3 plates on the gearbox!!!!! i will take some more pictures

[shaun5]

Here's the S4 fuel tank, going by the stickers, i would think its a replacement????

can someone show me where the tanks rust (ive searched but cant find any pictures)

[AndyP]

From what I've been told it's around the seam in the middle. Yours look pretty good, put some rust treatment on it and a good coat of underseal and it should be fine.

You know you can cut and splice ABS sensors? Done this on the S2, the rears are longer than the fronts and I couldn't find a good rear anywhere, so I just cut the cable off the old rear and joined it to a good front sensor

[UrS4boy]

Here's the S4 fuel tank, going by the stickers, i would think its a replacement????

All (most that I have found) big C4 Audi parts have part number stickers on them, even when they will never see the light of day after they leave the factory.

That 4A0201075A fuel tank will be an original, not a replacement. 4A0201075A was replaced on 01/03/2002 with 4A0201075L. 4A0201075L is listed as the replacement fuel tank for the C3 as far back as 1985 and the C4 as late as the last cars built in 1997, including the S6plus. It is also the V8 replacement fuel tank.

I say "is" like it exists in the warehouse. Probably dreaming, long gone as NLA.

[shaun5]

man is there anything you dont know

[shaun5]

From what I've been told it's around the seam in the middle. Yours look pretty good, put some rust treatment on it and a good coat of underseal and it should be fine.

You know you can cut and splice ABS sensors? Done this on the S2, the rears are longer than the fronts and I couldn't find a good rear anywhere, so I just cut the cable off the old rear and joined it to a good front sensor

This tank does look in good nick, thats why i thought it might be a replacement, So i just need to get rid of the rust and apply treatment, some more work to do in the evenings.

I've got quite a few old sensors so i will probably give it a go, i like to have all the correct mounting lugs. I will be able to slide them onto the new / replacement sensor wire

[Vorsprung durch Technik]

man is there anything you dont know

Always in you back pocket or in my case on the laptop....very convenient.