Audi 80 B4 Quattro sedan with a V8 engine :)

[macspring]

@ macspring:

I can give you the picture in a very large resolution

Received with thanks and proudly installed.

[[sTeeWie]]

@ Vorsprung durch Technik: You look right. This is your old Delta CC ... Right, it's volcanic black

I got it wrong. The paint is Panthero Black.


@ Ruffiano: That's right, it's your old taillights

@ Klobsters: Should I even find Recaros in platinum gray, so these are still installed … A cleaning system is mandatory only with xenon light.

@ Az786: Currently 8x18 "ET42 are fitted with 15mm distance.

@ Vauhtiveikko: Those were Advanti Racing Turba in 8.5x18 "ET40 and 5mm distances.


Thanks for the positive comments

I am currently considering whether I should again obstruct Avus wheels?
But I also like the BBS

[Vorsprung durch Technik]

I got it wrong. The paint is Panthero Black.

Thanks for the positive comments

I am currently considering whether I should again obstruct Avus wheels?
But I also like the BBS

Your welcome the car deserves the many praises!

Panthero Black,niiiiiice,was a B3 colour up till 1991 ish a very rare colour and one Audi should bring back!

I like the BBS and those other Avus but the S8 D1 alloys would look even better.

[[sTeeWie]]

My sedan is built in the end of 1992. The paint was sprayed at the factory. I love this color

The D2 Avus wheels of 1st generation like me, but not as good as the 2nd generation and indicate the Avus from S4 B6. But that is a matter of taste




On weekends, we have built a new lift with us in the hall. After a year without there was also time again. The Audi was quickly up and I'm surprised. Everything was great, except for a rear defective rubber grommet.

Here times still pictures, which I made yesterday.
Good also to see how sitting top mounts.

And not to forget. Somehow missing since 3 nuts on the exhaust manifolds














Here again images of the exhaust system. The pipe connectors have already come new. The old ones were leaky.

[Az786]

What size spacers are you using with the bbs split wheels?

[LucheS2@20v]

Nice car.How do you feel the heavier front end with this v8?

[Henkjan]

legend says the V8 is about the same weight as a 5 pot

[[sTeeWie]]

I use 15mm spacers per wheel.

That's true. The V8 engine weighs no more than a 5 cylinder. Thanks to aluminum motor it is easy.

[[sTeeWie]]

Last weekend, I once had the opportunity to test 8.5x19 "with 225/35 tires from a friend.

It's damn close. Full wrapping is not possible because then already pending, the tire in the wheel housing on the VA.

On the HA not millimeters proceeds inwards nor outwards. When fully eingefedertem wheel fits between the body and tires have a debit card

End of the story, it would probably. with another tire or a rim 8J.

Here times still images



















And finally, a small soundcheck

https://vimeo.com/148077175

[Error404]

Great project

[80Comp]

Looks good with the BBS Speedlines too..
19" is not to big for the b4 imo..
And a nice sound from the exhaust

[Holla]

Have you got some numbers for what the front, rear and the total weight is?

[[sTeeWie]]

I was not yet on a scale. But will be weighing in April the vehicle.

[Wizard-of-OD]

At the front, I built 6 piston Porsche Cayenne calipers with 360mm discs and 330mm at the rear wheels with S6 calipers.

What are the rear 330mm discs off of? Audi A8?

[[sTeeWie]]

In the first brake conversion with Audi S6 saddles, brake discs from the Audi S4 8K were used. These were turned off from the pot side.

In the current brake conversion with Audi S4 B7 saddles, brake discs from the Audi S5 were used.