Decided to sell all audi related parts i got during the years.Parts and bits are numerous,will describe here just some of them.
AAN engine block bored and honed to 81.5 mm with new Wosner pistons,new forged rods(i remember FCP but i could check),new Kolbenschmidt bearings,main and conrod bearings(conrod ones sputter)
AAN engine block sleeved at 81mm
AAN stock block needs rebore
AAN head,some small cracks
7A head,no cracks,with coolant rail mod and camshaft sensor bracket mod
AAN ecu NOT OPENED
AAN ecu PRJ software and map
AAN ecu(had MTM eproms in it if i remember correctly)
3b BROKEN ecu
AAN engine loom 2 pcs
coil conversion loom new
b2 digital dash,green,with original electric plug on rear
1 or 2 aan crankshafts
3 or 4 aan sets of camshafts
2 or 3 aan k24 7000 turbines
3 or 4 aan sumps
2.3 10v NA compleete engine
1 aby sump
1 rr NEW camcover
2 or 3 aan camcovers
oil pumps(3 or 4)
AAN intake manifolds(2 or 3)
AAN exhaust manifolds(2 or 3,one i remember crack free,the rest need to check)
wastegates and wastegate parts(maybe 3 compleete and some in parts)
Injector rails(2 or 3)
starters and alternators(i think 2+2 maybe more)
Will stop writing number of parts.Where i know for sure will do,where i do not remember consider at least 2 pcs/sets
aan engine alu mounts
coupe 5 cyl engine alu mounts
coolant rails,aan type and aby type
old and new r134 refrigerant s4 ac compressors(unknown condition)
steering pumps
b2,b3,b4 coupe subframes front and rear,some rear ones with stabi bar,some without.NO 01E front subframe.Just 01a and 016 FRONT SUBFRAMES
b2,b3,b4 coupe hubs front and rear.ALL 4 studs,NO S2 one
b2,b3,b4 coupe struts.NO S2
1 set of 7a coupe quattro sport suspension(h&r springs and billstein thick shocks,upside down system),shocks with no leaks
steering racks b2,b3,b4.NO RS2
1x s4 rear axle compleete with hubs,subframe,driveshafts,differencial
b2,b3,b2 coupe rear differencials
b2 gearbox with center diff lock 2 of them
b3,b4 01a gearboxes
1x01e gearbox 5 speed
If needed will look for codes on boxes and diffs.
s4 downpipes
1 set of 16 inch s6 c4 avus rims with center caps
1 set of 16 inch Borbet A 4x108 rims
s4 avant leather interiour(seats,door cards)
S2 crossmember and intercooler
s2 front bumper with signals,fogs and grills
s2 rear bumper
s2 front headlights NOT lens type
s2 coupe trunk cover
tons of sensors,brackets,oil and coolant lines,MAF etc etc
3 victor reintz head gaskets with lots of other new gaskets,seals etc
crank sprockets with no cracks
dual mass flywheels
single mass flywheels(1 i think is RR and one 3b)
intake and exhaust valves,springs retainers and 30 or 40 new valve guides
b2,b3,b4 and c4 brake calipers.Front single piston,front girling 2 piston,front s6 4 pads type.Rear not vented disc type and vented disc type
And much more.Parts are in boxes(new ones and small ones) and in a small place that will take my all shop and stop me from working if i get all out and try to get exact inventory.Could do some pics with heads,engines and some other parts that are easy accesible.
ALL THIS + 1985 b2 coupe quattro.Sandblasted where needed,epoxy primer,all covered in sprayabble rubber sealant and repainted.Has no door cards on,i have some sets but in bad condition.Also engine bay not refurbished.Has new fuel and brake lines,But suspension and bushings need redone.My idea was to have it painted,all underbody perfect and sandblast/powdercoat a full suspension,subframes etc,replace all bearings and rubbers and have all fresh.But i just managet to paint it 2 or 3 years ago and that was it.Car has driver seat recaro,new windscreen,new rear black lights.Have documented the restoring to this point,so i could supply pics.
I have a recent clip with the b2.
I would sadly let all this go for 18.000 eur.
AAN engine block bored and honed to 81.5 mm with new Wosner pistons,new forged rods(i remember FCP but i could check),new Kolbenschmidt bearings,main and conrod bearings(conrod ones sputter)
AAN engine block sleeved at 81mm
AAN stock block needs rebore
AAN head,some small cracks
7A head,no cracks,with coolant rail mod and camshaft sensor bracket mod
AAN ecu NOT OPENED
AAN ecu PRJ software and map
AAN ecu(had MTM eproms in it if i remember correctly)
3b BROKEN ecu
AAN engine loom 2 pcs
coil conversion loom new
b2 digital dash,green,with original electric plug on rear
1 or 2 aan crankshafts
3 or 4 aan sets of camshafts
2 or 3 aan k24 7000 turbines
3 or 4 aan sumps
2.3 10v NA compleete engine
1 aby sump
1 rr NEW camcover
2 or 3 aan camcovers
oil pumps(3 or 4)
AAN intake manifolds(2 or 3)
AAN exhaust manifolds(2 or 3,one i remember crack free,the rest need to check)
wastegates and wastegate parts(maybe 3 compleete and some in parts)
Injector rails(2 or 3)
starters and alternators(i think 2+2 maybe more)
Will stop writing number of parts.Where i know for sure will do,where i do not remember consider at least 2 pcs/sets
aan engine alu mounts
coupe 5 cyl engine alu mounts
coolant rails,aan type and aby type
old and new r134 refrigerant s4 ac compressors(unknown condition)
steering pumps
b2,b3,b4 coupe subframes front and rear,some rear ones with stabi bar,some without.NO 01E front subframe.Just 01a and 016 FRONT SUBFRAMES
b2,b3,b4 coupe hubs front and rear.ALL 4 studs,NO S2 one
b2,b3,b4 coupe struts.NO S2
1 set of 7a coupe quattro sport suspension(h&r springs and billstein thick shocks,upside down system),shocks with no leaks
steering racks b2,b3,b4.NO RS2
1x s4 rear axle compleete with hubs,subframe,driveshafts,differencial
b2,b3,b2 coupe rear differencials
b2 gearbox with center diff lock 2 of them
b3,b4 01a gearboxes
1x01e gearbox 5 speed
If needed will look for codes on boxes and diffs.
s4 downpipes
1 set of 16 inch s6 c4 avus rims with center caps
1 set of 16 inch Borbet A 4x108 rims
s4 avant leather interiour(seats,door cards)
S2 crossmember and intercooler
s2 front bumper with signals,fogs and grills
s2 rear bumper
s2 front headlights NOT lens type
s2 coupe trunk cover
tons of sensors,brackets,oil and coolant lines,MAF etc etc
3 victor reintz head gaskets with lots of other new gaskets,seals etc
crank sprockets with no cracks
dual mass flywheels
single mass flywheels(1 i think is RR and one 3b)
intake and exhaust valves,springs retainers and 30 or 40 new valve guides
b2,b3,b4 and c4 brake calipers.Front single piston,front girling 2 piston,front s6 4 pads type.Rear not vented disc type and vented disc type
And much more.Parts are in boxes(new ones and small ones) and in a small place that will take my all shop and stop me from working if i get all out and try to get exact inventory.Could do some pics with heads,engines and some other parts that are easy accesible.
ALL THIS + 1985 b2 coupe quattro.Sandblasted where needed,epoxy primer,all covered in sprayabble rubber sealant and repainted.Has no door cards on,i have some sets but in bad condition.Also engine bay not refurbished.Has new fuel and brake lines,But suspension and bushings need redone.My idea was to have it painted,all underbody perfect and sandblast/powdercoat a full suspension,subframes etc,replace all bearings and rubbers and have all fresh.But i just managet to paint it 2 or 3 years ago and that was it.Car has driver seat recaro,new windscreen,new rear black lights.Have documented the restoring to this point,so i could supply pics.
I have a recent clip with the b2.
I would sadly let all this go for 18.000 eur.
Comment