My 95 S2 Avant Project. LZ5T Coolness

[hunker7]

would that seal kit work on my UrS4?

[Error404]

No bearing. There are steel sleeves pressed into the alloy casing.

[hunker7]

I always thought there is a ball bearing inside somewhere, learn something new every day And thanks for the link

[irishs2]

Can't wait to see this one finished It will be better than new

Btw, where did you buy PAS pump seal kit, and did you change bearings too?

Thanks

I got this one
http://www.ebay.ie/itm/221441279876

http://rennbay.com/Power-Steering/Power-Steering-Pump-Seal-Kit.html

I didnt see a bearing in that pump. It just runs on oil on the casing itself.

[hunker7]

Can't wait to see this one finished It will be better than new

Btw, where did you buy PAS pump seal kit, and did you change bearings too?

[irishs2]

Movement has been slow these last few months, work has been busy and other projects have come and gone, and just got planning permission for my house so its all go go go. One of those projects was my brothers Ural 750. (A russian copy of a old BMW side car)





Decided to tackle the interior again and put the seats out of harms way.


Before


After cleaning with glipton leater cleaner and conditioner.


Base frame before cleaning and servicing.

I wanted to swap the *** cushions, not because the drivers one is bad but just to even the wear.
The seat base has to be removed to swap the cushion.


The seat base cushion then is easy to remove


Bit by bit its looking like its coming together. Its proper airbag steering wheel will be refitted near the end of the project.


Sorry for the poor pic quality. Will get some better shots of interior in time.




Got some assorted oetiker single ear clips in, but was missing 30mm (28-31.6mm)
Have some on the way so I can finish some hard to reach hoses before access is cut off by other bits.



A cheap tool to crimp the o-clips.

[mihai_antony]

Well done, keep going!

[andy10v]

Very nice.

It must take ages to make a bracket to your standards!

[irishs2]

Stock location and its a 13 row.

[Error404]

Haha what size cooler have you got?
Are you installing in the stock location?

[Christophski]

Looking good. A lot of effort there. Puts so many of us to shame

[irishs2]

I really should do a list alright as I am a bit all over the place, but this weekend I was hoping to get the down pipe on , easier than I thought with the driveshaft heat shield off ( had visions of dropping the subframe again)
I spent most of today faffing about trying to build a bracket and ducting for the mocal oil cooler. That ended in failure

[Error404]

Well done mate, really coming together.
Have you got a "completion list" yet?

[irishs2]

I reconditioned the Powersteering pump. As seen elsewhere, the A6 pump is 120bar and the S2 pump is 100bar. By using the front of the A6 and the rear of the S2 pump I get a 100bar single pump that fits in the stock location.













I had to replace my cam pully, as it had cracked its keyway.


I also decided to torque up the crankbolt.
200nm +180deg. I got to 90deg before my 3/4" drive bent. (not shown)


Fitted a newly acquired RS2 downpipe thanks Alex, and and the stock turbo. Along with some new heatshielding. (non OEM)


Torqued down the head, took the pic in Stage II.
Stage I 40nm 1-12, Stage II 60nm, Stage III +180deg


Before


After

[irishs2]

I just saw this in the flesh yesterday. Absolutely stunning workmanship. As I said to Eric, I don't know how he'll be able to bring himself to get it dirty by driving it.

Thanks