Tweet
No i'm sorry didn't have any time for the car. Tomorrow i will take the car away for the winter so i can't work on it any more. Next year i hope i can finish the car and get some resolds 
-
1360kg/600Whp Avant
0-200km/h 9sec -
it is runing on the staring fuel enrichment the first 10sec after that it changes to the fuel map. moore fuel.
the lambda isnt wamed up after 10 sec so dont worry about close lopp before you got the engien started.Comment
-
Lambda should only enable after 45-60 seconds
I would increase req fuel or increase ve table
Go back to basic and work out the req fuel and compare it to your current valueComment
-
Guys, the fellow just started the car to make sure nothing is going to go wrong, and he is going to store it.
the lamda wasnt even mounted on the downpipe, it was just hanging from the wastegate opening. Even if all settings were correct, it would still read lean as it is in open air.
More advice next year!Comment
-
You are totally correct. More fun next year. Will keep you all updated.
Tanks1360kg/600Whp Avant 0-200km/h 9secComment
-
Some news!
Finally the car is ready! My tuner did some work on it bud hey didn't get it running nice. When you give some gas it just dies around 1750/2000rpm. Turns out to by a bad primary trigger signal. Got lots of trigger errors.
To by sure i connected a oscilloscope and did some measurements.
As you can see i did measurements on the primary(Crank position VR sensor) and the secondary (cam position Hall sensor). Cam sensor looks good to my. It has some spikes but i don't think it will cause a problem.
The measures on the crank-position looks really bad. Not uniform at all. I pulled the sensor and noticed the flywheel pin (7A) Was only half in-front off the sensor. The machine-shop has removed the pin for lighten the flywheel. Is it possible so mount the pin to much in the flywheel?
After that i read lots off problems with the 7A flywheel pin. I decided to go the 60-2 trigger rout. Placed a OE VW 60-2 trigger-wheel on the car today. Its a Hall trigger.
Will tell you all more as soon as possible. Just have to make a appointment with my tuner again...1360kg/600Whp Avant 0-200km/h 9secComment
-
What is the partnumber and how much did you payed for it?Go Holset or Go RS4Comment
-
I'd be interested as well
sent with Nokia 6210Comment
-
The Parnumber from the flange are 030103171 LOriginally posted by Billman View Post
The Sensor is from VW Lupo.030906433Q
~100€
works good as well for my carComment
-
Also running on VEMS? When going from the VR sensor to Hall did you made some changes inside the VEMS?Originally posted by AudiS2Turbo View Post
Seal/60-2 030 103 171 L € 76.25
Sensor 030 906 433 Q € 54.55
Connector 1J0 973 723 € 3.42
Yellow wires 000 979 133 A € 1.88 each1360kg/600Whp Avant 0-200km/h 9secComment
-
Yes with Vems.Spoke with Katalyn for the changes.You must have 5V Outputsource for the Hall IC.
I think you must set a (in German->Lötjumper) from VR to Hall
GreetsComment
-
Rebuild for hall on Primary:
Make a short-curcuit on the top "blob" and open-up the lower one
Change This resistor to ~2,7kohm
Rebuild for hall on Secondary:
http://www.vems.hu/wiki/index.php?pa...AudiECUrebuildComment
-
Oh wonderful Erik.It looks good!
Gesendet von meinem GT-I9100 mit Tapatalk 2Comment
Comment