Cheers for the information. I'll look into it all.
Announcement
Collapse
No announcement yet.
abs sensor
Collapse
X
-
Any advice which abs sensors will fit directly on CQ20V? I need a 2 rear and 2 front ABS sensors, OEM numbers are 893 927 803 or 893 927 803 A for the front and 893 927 807 C or E for the rear. What number is correct for 7A Coupe Quattro?ETKa does not show wich number is for which engine. Should i use a different OEM number of sensor, for others vehicle?
So 8D0927807C for the rear, with cut off a connector and use old one?
What about 4A0927807 ?
Or use 2 pieces 4A0 927 803 for the rear?Looks the same as Old ones...same connector...Maybe it works 4 pieces for rear and front too?
Does anyone know OEM lenght of sensors? rear and front?Last edited by Tom_; 7 March 2017, 14:00.Audi Coupe Quattro 2.3 20V
Comment
-
On my 90 q 20v I used 100/A6 front sensors - they're about £15 for after market ones. Same connector - only difference is the cable length which is about 2" longer
For the rear I used A4 avant rear sensors and swapped over the original connectors. Think I swapped the grommet as well while the connector was offMike
http://www.s2-audi.co.uk
Comment
-
I measure the pin holes of sensors
Drivers front - 1,20 kOhm
Drivers rear - Nothing change, so i guess dead)
Codriver rear - 1,18 kOhm
Codriver front - Nothing
is that just luck or some pattern? That goes cross ? Any suggestions?
Mike, do you have a OEM numbers?Thank you
What is difference between OEM front and rear sensors except oem number?Looks same, only lenght is different...Last edited by Tom_; 7 March 2017, 16:53.Audi Coupe Quattro 2.3 20V
Comment
-
The rears have a different type of grommet as it seals off the floor under the car and they're different lengths. The actual sensor itself is the same
Here's the numbers I used
8D0927807C - rear
4A0927803 - frontMike
http://www.s2-audi.co.uk
Comment
-
U mean this seal on the picture, where is a mark?It could be reused again from OEM sensor, couldnt it?
Thank you MikeAudi Coupe Quattro 2.3 20V
Comment
-
Originally posted by S2_avant 19930325 View PostI have a s2 avant - 93.
If i want to mount ABS can i use these sensors ?
8D0927807C - rear
4A0927803 - front
I understand i have to fit some kind of rubbersealant , because i dont have any sensors today at all.
Comment
-
why not just cut the cable in the appropriate place, thread on the crimp socks, solder and voila, u have a perfect match
For 80 avant :
according to etka (rear Quattro) 8A0927807C :
8A0927807C.jpg
and front 893927803A :
893927803A.jpgLast edited by pfi; 23 July 2021, 18:04.
Comment
-
Originally posted by Tonybolony View Post'Fuel Parts AB1172 ABS Sensor'
or
Intermotor 60263
Both @ £14
Unless it has recently been changed- the AB1172 is still on (and working??) on a certain ruby red avant that's in your part of the world, Andy.
At worst, you may have to change the multi-plug.
Best Regards
Comment
-
Originally posted by pfi View Postwhy not just cut the cable in the appropriate place, thread on the crimp socks, solder and voila, u have a perfect match
For 80 avant :
according to etka (rear Quattro) 8A0927807C :
8A0927807C.jpg
and front 893927803A :
893927803A.jpg
893927803A , that one is a lot more expensive.
Hmm in the post before i asked if i can use the same sensor of that model on all for wheels, maybe the easier route to go.
Comment
-
Is the ABS pump 4A0614111E the only one thats fits ? Its the original OEMnr for my car.
Does the 4A061411B fit ??
It looks like 4A061411B replaced with 111E .. correct ?
Is it better to buy the newer replacemnt , it could be that the older model had some defect after a while that they discovered and ther for replaced it or to fit maybe more models. Difiicult to now.
Best RegardsLast edited by S2_avant 19930325; 28 August 2022, 11:51.
Comment
Comment