Bosch injector data.

[Flat on my back]

Would like to check the data on a set of injectors...0 280 156 095.

Been on a site recently listed on here but the part no. wasn't shown.?

Can someone help?

Cheers.

[Audi Parts Guru]

Would like to check the data on a set of injectors...0 280 156 095.

Been on a site recently listed on here but the part no. wasn't shown.?

Can someone help?

Cheers.

It's fitted to the Ford Focus, 173 bhp engine

1, Resistance 14.5 ohms
2, Flow rate 175.4 cc per min @ 2.7 bar fuel pressure
3, Bosch EV 6.2L injector type

Hope that helps

[Flat on my back]

Hmmmmmm...

Not sure if that's going to help get to 200 hp in my 7A, unless the extra fuel pressure is the reason.

Now where's that injector calculator gone...

Thanks.

[Audi Parts Guru]

Not sure if that's going to help get to 200 hp in my 7A, unless the extra fuel pressure is the reason.

Now where's that injector calculator gone...

Thanks.

Forget it, these are high resistance injectors and if I remember correctly, the 7A injectors are low resistance

Also, increasing the fuel pressure will make very little difference, if any, in terms of fuel flow rates

[spink]

Forget it, these are high resistance injectors and if I remember correctly, the 7A injectors are low resistance

that's right but if you bypass the injector pack in the scuttle panel you can used high impedance injectors.

[Audi Parts Guru]

that's right but if you bypass the injector pack in the scuttle panel you can used high impedance injectors.

Maybe so, but the 7A injectors are made by Hitachi, and lets just say that they're not exactly the best injector manufacturer in the world

Give me a set of Bosch injectors any day

[Flat on my back]

.

Bypassed already with a set of Bosch .jectors fitted.

Will have to get the no. tonite and see wot you think.

[Flat on my back]

Right...

Wot i have fitted now is a set of supposably equivalent/slightly better bosch .jectors part no. 0 280 155 931.

Found some data on these but does someone have a pdf data sheet on these 2 i mentioned so i can compare and contrast to find the best one?

Mr 'Guru' wot does one think of these 2?

[Audi Parts Guru]

Wot i have fitted now is a set of supposably equivalent/slightly better bosch .jectors part no. 0 280 155 931.

Found some data on these but does someone have a pdf data sheet on these 2 i mentioned so i can compare and contrast to find the best one?

Mr 'Guru' wot does one think of these 2?

Forget it, these are fitted to a great big Holden 5.7 litre V8 producing 300 bhp

Unfortunately I don't have the full specs on these injectors

[Flat on my back]

Jesh...

Ones not a happy bunny now...both sets were purchased from a reputable source, the
...931 as a replacement Hitachi set and the ...095 as an upgrade to go with the v6 maf mod on the 7A engine...arje...

Any idea on a replacement for these Hitacky sprinkler jobs...

[Audi Parts Guru]

Ones not a happy bunny now...both sets were purchased from a reputable source, the
...931 as a replacement Hitachi set and the ...095 as an upgrade to go with the v6 maf mod on the 7A engine...arje...

Any idea on a replacement for these Hitacky sprinkler jobs...

Might cost you a bit more but i'm sure it'll be worth it

http://www.034motorsport.com/product_info.php?cPath=24&products_id=329

[20Vcqdriver]

Injectors

Carl,
The upgraded injectors for the MAF were specced up by 034EFi and worked great in my set up. Whats the issue with them?! They may also be for a holden but from memory that uses a higher fuel pressure which does make a big difference!