Crankshaft pulley bolt for Stroker

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Billman
    S2Forum Freak
    • Nov 2004
    • 4129
    #1

    Crankshaft pulley bolt for Stroker

    Hi, I have noticed today that the winding in the AEL diesel crank is far back compared to the rs2 crank so that the stock bolt does not fit (too short)!

    What sk you use there? The diesel bolt or an aftermarket one?
    Go Holset or Go RS4
    Tags: None
    • Billman
      S2Forum Freak
      • Nov 2004
      • 4129
      #2
      Some help please
      Go Holset or Go RS4

        Comment

        • repo
          S2Forum Maniac
          • Dec 2004
          • 893
          • Country: Finland
          #3
          I used diesel bolt.
          Everything less than 2 bar is considered to be naturally aspirated

            Comment

            • Billman
              S2Forum Freak
              • Nov 2004
              • 4129
              #4
              Ok, I have to order an AEL then!!!
              Go Holset or Go RS4

                Comment

                • Billman
                  S2Forum Freak
                  • Nov 2004
                  • 4129
                  #5
                  The genies at Audi gave instead of the AEL crankshaft bolt (N 904 980 02) the V6 and other TD bolt (059 105 229).

                  The difference in general is that the AEL is Hexagon M18x1,5 and 110 length and the other one is Twelve edges M18x1,5 and 98 length.

                  Dont know the hardness of the AEL block but the RS2 one is 12,something anf this one i got now is 11.0

                  should i give it back or should i use it. I believe the lenght is of no issue.
                  Go Holset or Go RS4

                    Comment

                    • AndyP
                      S2Forum Zealot
                      • Feb 2004
                      • 6049
                      • Country: England
                      #6
                      Given the massive torque setting on these I'd get an AEL one. The length should not be a problem but if it's not 12.9 grade then this will be.
                      sigpic
                      1991 Audi S2 3B - 2.5 Stroker engine
                      1997 A6 2.5TDi quattro avant - C4
                      1976 RD250E / 350LC cafe racer

                        Comment

                        • Jamo
                          Retired OG Mod
                          • Mar 2004
                          • 21750
                          • Country: United Kingdom
                          #7
                          Originally posted by AndyP
                          Given the massive torque setting on these I'd get an AEL one. The length should not be a problem but if it's not 12.9 grade then this will be.
                          Diesel ones are not grade 12 BTDT

                          It's not a problem I asked around and Repo said use the diesel one

                            Comment

                            • Billman
                              S2Forum Freak
                              • Nov 2004
                              • 4129
                              #8
                              Both are diesel ones! Question is bring it back and get AEL or stick with it?
                              Last edited by Billman; 6 July 2010, 07:09.
                              Go Holset or Go RS4

                                Comment

                                • Jamo
                                  Retired OG Mod
                                  • Mar 2004
                                  • 21750
                                  • Country: United Kingdom
                                  #9
                                  Use the one appropriate to the your crank, mine was an AAT so I used the AAT bolt

                                    Comment

                                    • Billman
                                      S2Forum Freak
                                      • Nov 2004
                                      • 4129
                                      #10
                                      What Torque for these diesel Bolts?
                                      Last edited by Billman; 6 July 2010, 09:28.
                                      Go Holset or Go RS4

                                        Comment

                                        Previous template Next
                                        Working...

                                          We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                                          By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                                          I Agree