Intake manifold porsche inscription

[willg54]

I'd like two of these's depending on price,would it be possible to have it without the red filling?

I'll supply they as bare aluminium, no paint, no treatments etc so you can do what you like to make them individual.

As for cost, i think i'm working on around £20 +p&p "donation to my studies" to cover material, tooling, time programming etc and beer to fuel the technicians. Would you say this is reasonable?

[Big Lee M]

I'd like two of these's depending on price,would it be possible to have it without the red filling?

1. MadPugger - Audi Sport
2. MadPugger - Porsche
3. ALS2 - Audi Sport
4. quattrostyle
5. TimE-J - Audi Sport
6. vonbeck Audi sport
7. Dan - One of each
8. S2_WOT - Audi Sport
9. andy broke it - Either lol
10. bikerjim - Audi Sport (depending on price)[/quote]
11. jade - Audi Sport
12. HPmuirt - Audi Sport
13. Hoffer76 - Audi Sport
14. Willg54 - Audi Sport - cant forget myself!
15. Big Lee M - Audi Sport x2

[Nuvo]

The opened lettering looks much better now.

[willg54]

looking at spec'ing the material.

my choice goes with
6082 - great for treatments (anodising etc), high anti-corrosion - most expensive but not outrageous
5251 - great corrosion resistance, typically found in marine applications - bit cheaper
1050 - cant heat treat it, good corrosion resistance and cheap!

and 2 or 3mm? trying to source 2.5

[willg54]

comparison of the last 2

[willg54]

3rd try lucky!?

[Nuvo]

I was aiming to keep the capital a and s the same size height wise.

I agree with that decision.

[willg54]

That was a consequence of scaling it down. But my cad skills haven't been used up yet so I could be able to open it a little.

I wasc aiming to keep the capital a and s the same size height wise.

I'll play some more

[Nuvo]

with the itallic 'sport' and all lower case powered by.

made the plate a bit smaller according to the recess measurement on my manifold.

That looks really good, is it possible to "open up" the Sport font like that before as it appears a little skinny or is this a consequence of scaling down the area of the plate?

[willg54]

1. MadPugger - Audi Sport
2. MadPugger - Porsche
3. ALS2 - Audi Sport
4. quattrostyle
5. TimE-J - Audi Sport
6. vonbeck Audi sport
7. Dan - One of each
8. S2_WOT - Audi Sport
9. andy broke it - Either lol
10. bikerjim - Audi Sport (depending on price)[/quote]
11. jade - Audi Sport
12. HPmuirt - Audi Sport
13. Hoffer76 - Audi Sport
14. Willg54 - Audi Sport - cant forget myself!

[willg54]

with the itallic 'sport' and all lower case powered by.

made the plate a bit smaller according to the recess measurement on my manifold.

[willg54]

can people do me a favour and measure the recess on your inlet manifold? i make mine 32mm x 315mm ish...

cheers!

[willg54]

The design looks really good so far.

I've got a few suggestions you might like to consider.
I think the "Powered By" text should use all lower case lettering to match the text used on RS2 manifold. I'm also thinking that the word "Sport" *might* look better italicised to follow the diagonal lines of the Audi sport logo.

Points taken! I'd like it to look authentic so i'll see what i can do!

[TimE-J]

Looking good will, that's exactly what I'm after!

[Nuvo]

The design looks really good so far.

I've got a few suggestions you might like to consider.
I think the "Powered By" text should use all lower case lettering to match the text used on RS2 manifold. I'm also thinking that the word "Sport" *might* look better italicised to follow the diagonal lines of the Audi sport logo.