Announcement

Collapse
No announcement yet.

gearbox 6 speeds 01e CBL s4 in audi s2 3b

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    I have problems with the linkage of the gearbox
    I'm trying to adapt one that I have here from a6 tdi but it does not look good
    The linkage of Audi S4 is mounted directly or there to make any changes?

    Comment


    • #17
      is already mounted
      I also made the supports

      Comment


      • #18

        Comment


        • #19
          Originally posted by Nuno_Cristiano View Post
          I did same convertion in my Coupe 20V and i used:

          - CBD gearbox 01E from S4 5 speed
          - Gear mounts from a guy here in forum that sell this parts works fine to use original subframe ( B3 ) ( i can check my PM to see name of user )
          - Linkage from S4 B5
          - propshaft cut in 26mm
          - convertion 4x108 to 5x112 but you not need because originally S2 is 5x112.

          Hope help you!
          Do you have the details of what/where you shortened the propshaft please?
          sigpic
          Tom C - www.rcmr.co.uk
          Audi UR Quattro
          Audi 100 C3 2.0 5 cyl 115ps
          Audi S2 - 07k engine project aiming for 800ps
          Audi B5 RS4 645ps 911nm

          Comment


          • #20
            I use Firow Propshafts in Cheshire
            Panthero Coupé quattro 20vt
            Indigo ABY coupé
            Imola B6 S4 Avant

            Comment


            • #21
              Originally posted by Nuno_Cristiano View Post
              I did same convertion in my Coupe 20V and i used:

              - CBD gearbox 01E from S4 5 speed
              - Gear mounts from a guy here in forum that sell this parts works fine to use original subframe ( B3 ) ( i can check my PM to see name of user )
              - Linkage from S4 B5
              - propshaft cut in 26mm
              - convertion 4x108 to 5x112 but you not need because originally S2 is 5x112.

              Hope help you!
              Who is making the gearbox mounts?
              sigpic
              Tom C - www.rcmr.co.uk
              Audi UR Quattro
              Audi 100 C3 2.0 5 cyl 115ps
              Audi S2 - 07k engine project aiming for 800ps
              Audi B5 RS4 645ps 911nm

              Comment


              • #22
                Just for information purposes, at least in the states, the 2002/03 B6 A4 3.0L V6 came with a 01E transmission. Code is FYF or GBE. You can also use the shift box out of it. These transmissions will be a little less beat on since they did not come behind a 2.7TT engine. They have the same gears ratios as the B5 S4.

                I have one in my car, and another on the shelf. If you have an ABY S2, the linkage from said S2 will bolt up to this trans. One added bonus, is that this trans comes with a OEM crank sensor, if you have a flywheel with a 60-2.

                Greg W.
                They can have my car when they pry my cold dead fingers from the steering wheel.

                Comment


                • #23
                  Originally posted by audiman View Post

                  Who is making the gearbox mounts?
                  Contact user
                  bn-01-wso
                  .: Audi Coupe Quattro 20V 91' :.
                  .: Audi/PorscheRS2 95' :.
                  .: Mitsubishi 3000GT VR-4 96' :.

                  Comment


                  • #24
                    B5 propshaft parts are of absolutely no use to fit into an S2 coupe.
                    sigpic
                    Tom C - www.rcmr.co.uk
                    Audi UR Quattro
                    Audi 100 C3 2.0 5 cyl 115ps
                    Audi S2 - 07k engine project aiming for 800ps
                    Audi B5 RS4 645ps 911nm

                    Comment


                    • #25
                      Tom, there is a place in Bristol that will shorten and re-balance the 5-speed prop. £100 and takes a couple of days.
                      91 Modded 3B
                      14 A6 Avant Black Edition

                      Comment


                      • #26
                        http://www.prop-shaft.com/
                        91 Modded 3B
                        14 A6 Avant Black Edition

                        Comment


                        • #27
                          Are the s2 108mm driveshaft flanges the same
                          part number front and rear or are they different?

                          Comment


                          • #28
                            Originally posted by orignalS60 View Post
                            Are the s2 108mm driveshaft flanges the same
                            part number front and rear or are they different?
                            No, they are not the same. The rear diff flange are specific to the ABY S2. The left side has a is set up for a Lock diff switch. The right side has a different part number than the trans flanges.

                            Greg W.
                            They can have my car when they pry my cold dead fingers from the steering wheel.

                            Comment

                            Working...
                            X