From CGR to CRB gearbox upgrade

[Audi-Porsche Avant RS2]

Thanks a lot!
Bye

Alessio

[2226]

Hi Alessio

Have a look at http://www.elektro.com/audi/01E/ to see what you can learn there - perhaps you could email elektro for some advice.

[Audi-Porsche Avant RS2]

Seriously......?

Try your local audi dealer / audi specialist / gearbox rebuilder.

Yes, seriously, my problem is know what I must change for my problem when I chage from 1st to 2nd gear at high rpm.

Alessio

[fish]

My S2 is a 94 and has the CGR with wide first gear, 1 owner before me. Would be very surprised if he didn, t tell me about a gearbox change and the servicebooklet clearly says CGR

[Kieron20V]

I pay who help me with this issue

Seriously......?

Try your local audi dealer / audi specialist / gearbox rebuilder.

[Audi-Porsche Avant RS2]

I pay who help me with this issue

[Audi-Porsche Avant RS2]

UP

For resolve my problem I must change only 012 311 247 F synchronizer ring or I must change 01E 311 239 H synchronizer body?

This week I will open the gearbox

Thanks a lot friends!

Alessio

[Audi-Porsche Avant RS2]

Thanks a lot Andy!

For resolve my problem I must change only 012 311 247 F synchronizer ring or I must change 01E 311 239 H synchronizer body?

Thanks!

Alessio

[AndyP]

Yes

[Audi-Porsche Avant RS2]

Hello friends, is possible to change 6 speed ABY linkage with the gearox mount on the car or not?
Thanks a lot!
Bye

Alessio

[Audi-Porsche Avant RS2]

Hello, please someone can tell me if for resolve my problem I must change only 012 311 247 F synchronizer ring or I must change 01E 311 239 H synchronizer body?

Thanks a lot!

Bye

Alessio

[Audi-Porsche Avant RS2]

Hello, please can you post it the codes of the parts that I must change for resolve the problem?
Is only 012 311 247 F synchronizer ring or is 01E 311 239H synchronizer body?
Thanks a lot!
Bye

Alessio

[madpugger]

Audi should be able to sell you a syncro yes. It will not be the pressure plate you are correct.

The syncromesh - Basically when you are in 1st the engine and gearbox input shaft are doing a set speed to do that road speed. When you want to change up to 2nd, doing the same road speed, the input shaft need to turn slower. When you press the clutch to change gear the input shaft doesn't slow down in the 0.5 of a second it takes you to change So the syncro does what the name says, it sycronises the speed of the two cogs so the can mesh together. It is basically like a clutch for the individual gears. It is usually 2nd gear that goes because this is normally where you are trying to quickly change gears thus putting more wear on the gears.

I hope that helps you!

[Audi-Porsche Avant RS2]

This problem is likely your syncromesh for 2nd gear. You could risk a second hand box and hope it does not have the fault, or you could buy a new syncro, IIRC it will be a syncro with gear, and replace it.

The problem is unlikely to be because you don't have the wide 1st IMO

Hello, I have already another gearbox, but I don't know if have the same problem or not, can I find the original syncro from Audi dealer?

I think that the problem can't be the pressure plate, because I have this problem only when I go up very fast from 1st gear to 2nd gear and the engine run at high rpm.

Alessio

[BIGGYIN]

Glad to help.
Bought the manual,because someone on here was selling a damaged(cheap) CGR box.
Got manual,contacted guy about box.GONE.
Atleast someone,s got abit of use out of it.
Karl.