Originally posted by igsya
View Post
Announcement
Collapse
No announcement yet.
6 Speed into an Ur Quattro
Collapse
X
-
Originally posted by Bram View Postscan the article and post the PDF here please?1986 Coupe q - 2281cc 3B, chargecooler, 2.75" exh & downpipe, ported head, water injection, CGR box, modified MD357 turbo, 440cc injectors, high power coil.
2004 A4 2.5TDi convertible, re-mapped to 180bhp
2011 A5 sportback 3TDi-Backbox delete, remap
Comment
-
-
Originally posted by 20Vcqdriver View PostFile too big, have to send via e-mail to those interested, Soz
The shifter gate, no need to weld anything, combination of Ur-q and UrS4 parts can be bolted together with the same result, pics on my project page.
The shifter, same here, Ur-q shifter fits with ur-q ball on the UrS4 selector BTDT, no hitting of the floor or transmission, pics on my project page.
S2 6-speed mounts can be used with spacer on the pass side, no need for custom mounts.
Also, there is enough movement in the driveline and CVs that a 15 mm spacer for the back of the transmission is not needed.
I have a copy of the article on my site:
http://www.quattro.ca/6%20speed%20article.pdf
Hope this helps
Martinwww.quattro.ca
B2: 82 Urq into Sport quattro, 82 4000 2-door, 83 80q 2 Door, 83 Ur-q CDN, 85 Ur-q Euro with 3B, 86 4kq, 59,000km
B3/B4: 91 CQ, 93 90q 2.5TDI, 94 80q avant 2.5tdi, 94 S2 Avant
Comment
-
are you guys retrofitting the mechanical speedo into the o1e or going elec speedo on the dash w a 5ktq unit?BEAST '90 CQ 24v VRT / O1E / v8 rear, HOLSET SUPER 40 http://www.theprojectpad.com/viewtop...1&t=193#p37887
DD '86 4kq BLAZE, swapping aba/16vT and O1E http://www.theprojectpad.com/viewtop...1&t=201#p38264
Comment
-
I just put in digidash, but if you read the article it will explain how to get the mechanical components in there (all 4kq stock parts).
Hope this helpswww.quattro.ca
B2: 82 Urq into Sport quattro, 82 4000 2-door, 83 80q 2 Door, 83 Ur-q CDN, 85 Ur-q Euro with 3B, 86 4kq, 59,000km
B3/B4: 91 CQ, 93 90q 2.5TDI, 94 80q avant 2.5tdi, 94 S2 Avant
Comment
-
Originally posted by ralleyquattro View PostI just put in digidash, but if you read the article it will explain how to get the mechanical components in there (all 4kq stock parts).
Hope this helps
we are currently working on using a 5ktq speedo in the 4kq clsuter for elec speedoBEAST '90 CQ 24v VRT / O1E / v8 rear, HOLSET SUPER 40 http://www.theprojectpad.com/viewtop...1&t=193#p37887
DD '86 4kq BLAZE, swapping aba/16vT and O1E http://www.theprojectpad.com/viewtop...1&t=201#p38264
Comment
-
martin, just a few things i need get sorted
i am using an usdm urS4 5 speed o1e
i now have the 4kq outer cv's on b3 front axles
( are they coupe and 90 axles same length? and also side to side?)
the front drive cups are 4kq front 016 units in the o1e
it seems as though they stick out too far from the box, the drivers side 4kq/90 axle works but seems jsut a bit snug and the passenger wont quite fit even with the balljoint fully extended
heres a pic of the axle cups, lmk if you think they are stickign out too far
are the urS4 o1e's and b5 6speed o1e's the same width?
ill get a pic here soonBEAST '90 CQ 24v VRT / O1E / v8 rear, HOLSET SUPER 40 http://www.theprojectpad.com/viewtop...1&t=193#p37887
DD '86 4kq BLAZE, swapping aba/16vT and O1E http://www.theprojectpad.com/viewtop...1&t=201#p38264
Comment
-
heres the pic LMK what ya think about it sticking out too farAttached FilesBEAST '90 CQ 24v VRT / O1E / v8 rear, HOLSET SUPER 40 http://www.theprojectpad.com/viewtop...1&t=193#p37887
DD '86 4kq BLAZE, swapping aba/16vT and O1E http://www.theprojectpad.com/viewtop...1&t=201#p38264
Comment
-
You need to shave 3mm from the inside of the flange (spline end).
That's all.www.quattro.ca
B2: 82 Urq into Sport quattro, 82 4000 2-door, 83 80q 2 Door, 83 Ur-q CDN, 85 Ur-q Euro with 3B, 86 4kq, 59,000km
B3/B4: 91 CQ, 93 90q 2.5TDI, 94 80q avant 2.5tdi, 94 S2 Avant
Comment
-
Originally posted by ralleyquattro View PostYou need to shave 3mm from the inside of the flange (spline end).
That's all.
on the inside spline end there is a tapered cone just liek on the inside of the cup for the fixing bolt.
can the spline be cut shorter and flat? or do i need to lathe that cone farther into the spline as well?BEAST '90 CQ 24v VRT / O1E / v8 rear, HOLSET SUPER 40 http://www.theprojectpad.com/viewtop...1&t=193#p37887
DD '86 4kq BLAZE, swapping aba/16vT and O1E http://www.theprojectpad.com/viewtop...1&t=201#p38264
Comment
Comment