Announcement

Collapse
No announcement yet.

Driveshafts lengths and info

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Driveshafts lengths and info

    Front driveshafts from S2/RS2 or 90/Coupe89 7A 20V FWD manual transmission.
    28 inner splines for 108mm inner CV.
    27 outer splines for big outer CV (38 splines, 82mm bearing).
    Naked shafts lengths: 517 & 531mm.
    Attached Files
    Last edited by _ShurikeN; 6 April 2017, 20:08.

  • #2
    Rear driveshafts from Audi 80 B4 Avant (Non-ABY).
    33 inner splines: 100mm inner CV originally, but 108 affordable (VW T4/T5 IIRC).
    25 outer splines for medium/big outer CV (38 splines, 82mm bearing).
    Bare shafts lengths are 535mm each.
    Attached Files

    Comment


    • #3
      Originally posted by _ShurikeN View Post
      Front driveshafts from S2/RS2 or Coupe89 7A FWD manual transmission.
      28 inner splines for 108mm inner CV.
      27 outer splines for big outer CV (38 splines, 82mm bearing).
      Naked shafts lengths: 517 & 531mm.




      RS2'd 93 UrS4 5 spd sedan
      94 UrS4 V8 6 spd manual avant

      Comment


      • #4
        "Weak" front driveshafts from small motor saloon FWD or Quattro.
        33 inner splines: 100mm inner CV originally but 108mm possible (VW T4/T5).
        30 outer splines: originally small outer CV with 33 splines, 75mm bearing. Medium/large outer CV possible (audi 100 C4 with weak engines).
        Lengths: 521 & 535mm.
        Last edited by _ShurikeN; 6 April 2017, 20:20.

        Comment


        • #5
          Photos of Error404 from 'for sale' section, I hope he does not mind.
          7A ACOQ rear shafts. They are shared across many non-turbo ACOQ-s (ABC,AAH,NG, NM) and 5-cyl 90 B3. 33 inner teeth. 30 outer teeth.
          Aproximately 535 and 502mm from what can be seen on photo.
          Attached Files
          Last edited by _ShurikeN; 5 August 2019, 19:09.

          Comment


          • #6
            Good thread
            Panthero Coupé quattro 20vt
            Indigo ABY coupé
            Imola B6 S4 Avant

            Comment


            • #7
              Sorry for bringing such an old thread back up but it’s very hard to find information on driveshaft length.
              Does anybody have the length of S2 coupe rear shafts? I have a pair but the difference in length is more than I was expecting and I am having issues fitting them. My set up is far from stock so it might not be the shafts that are the issue. I was surprised how different they are compared to fronts which are much closer in length.

              Comment


              • #8
                Few posts up.
                Aproximately 535 and 502mm
                1989 Audi 80 Quattro
                1994 Audi 80 Quattro Competition

                Comment


                • #9
                  That’s says non turbo cars so are we saying the S2 coupe shafts are the same just with a 108mm inboard cv joint?

                  Comment


                  • #10
                    Should be, as the rear axle geometry is the same. Same diff, same subframe, same hub carriers. Spline count and thickness maybe different.
                    1989 Audi 80 Quattro
                    1994 Audi 80 Quattro Competition

                    Comment


                    • #11
                      Spline count is different. Thickness is the same as 7A can vouch for that. Possibly 2.8 and 2.6 as well.
                      1990 2.2 20VT Audi Coupe Quattro
                      *Hx35/k26, MaxxECU, Wagner EM/IC *RS2 Recaro *4pot-Brembo *3" turboback *Treser *Koni/H&R
                      1990 Audi 200 20v Avant 2.2 20VT *7 Seater *Full electric gizmos

                      Comment


                      • #12
                        Rear driveshafts from Audi 80 B3 typ89 Quattro saloon with 4 cylinder engine. Partnumbers of shafts assemblies with joints should be 893501203H and 893501204H according to catalogs. The cat claims they are also from Audi Coupe Quattro typ89 KV/NG.

                        509mm left, 551mm right. 33 inner splines, 30 outer splines.
                        Attached Files

                        Comment


                        • #13
                          Originally posted by G60Rallye View Post
                          That’s says non turbo cars so are we saying the S2 coupe shafts are the same just with a 108mm inboard cv joint?
                          S2 coupe rears 545mm and 503mm

                          Comment


                          • #14
                            Does anyone know which way around the front shafts go? ie the longer one is which side?

                            Comment


                            • #15
                              I am not 100% sure but from my informaton driver side is shorter;
                              51.7mm uk driver side
                              53.1mm uk passenger side
                              this is dimension for bare shafts

                              Comment

                              Working...
                              X