Launch control for Motronic

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Ross
    replied
    I'd like to see this on the RS2, must admit it's pretty brutal as-is if you do a 4k launch. I've only ever done one, too much drivetrain sympathy

    Leave a comment:


  • Rocco
    replied
    nice Paul¡¡

    Leave a comment:


  • S2central.net
    replied
    Results of 1st back to back tests of VLC versus stock ECU. Remember that the ONLY change in code is the addition of VLC - Variable Launch Control.

    I was expecting an improvemnt of 0.1 - 0.2s in 60ft times but ended up with 0.3s

    More tests to come. Dmitri & I have cooked another little refinement for adjustment at higher revs but nobody else need worry about that.

    Now - I am no drag queen - ooops that came out wrong... I dont get it perfect every time - but with VLC enabled it is a LOT easier to get a clean get away with a good swirl of wheelspin and then the G-force hits your guts.

    Running uprated chips with VLC will come next - my poor old car is an R&D shed now
    Attached Files

    Leave a comment:


  • prj
    replied
    Originally posted by Ruffiano
    you should try with a k24 7400...
    I will as soon as I get it attached.
    Won't be long now.

    Leave a comment:


  • Ruffiano
    replied
    Originally posted by prj
    It will be less. Need to try.
    you should try with a k24 7400...

    Leave a comment:


  • Rusty
    replied
    OK, cheers

    Leave a comment:


  • prj
    replied
    FFS would only be enabled if your TPS is over 90 or 95%.
    I don't think you press the throttle that much when blipping.

    Leave a comment:


  • Rusty
    replied
    How would the FFS kit affect throttle blipping during downshift, either during heel and toe or just rev matching? Would the clutch pedal need to be fully home to enable the engine to rev?

    Leave a comment:


  • prj
    replied
    Just chips and a switch under the clutch.
    Or to be more correct - one chip.

    Leave a comment:


  • mouse
    replied
    Originally posted by S2central.net
    Yes - this isn't just a case of wiring up any old pot to an unused ECU pin... There are some internal mods required on the ECU to make the unused input active and to get the voltage levels correctly balanced for operation across the revs - with boundaries that we have in the code to behave correctly if the pot is unplugged and when a clutch switch is detected in the future.

    I intend to offer the Variable Launch Control (VLC) as an upgrade to any 20VT ECU that includes the internal mods with a nicely connectorised loom that can be user installed for the pot location.... this will also be plug and play forwards compatible for features with the clutch switch to come in the future....
    So if Launch Control is installed would the ECU have to be sent in to add FFS in the future? Or just chips?

    Leave a comment:


  • A1quattro
    replied
    my rally car is only 1166kg so launch control should be pretty impessive ftom inside the car. even if it only saves me 1 second off the start line ,most rallys have 8-10 stages [the blackpool rally has25+] so 8 secnds + could get me that extra place at the finish ramp on the last event 3wks ago we were 7th o/a out of 91 cars only 6 seconds from being 6th ,the 6 cars in front were 1 wrc subaru,1 wrc focus,1 evo 9, 2 darrian [kit cars700kg ],and a bloody 1400cc/190bhp nova[700kg]we were in beating , 15 cars in our class, but i went off on stage 3 sorry its off topic [just fying the audi flag]

    Leave a comment:


  • Rocco
    replied
    Originally posted by prj
    It will be less. Need to try.
    ok try with mine

    Leave a comment:


  • prj
    replied
    Originally posted by Rocco
    Dmitri, with bigger turbos like k24 7200 or k26/27 ,how many boost will produce in the launch control??
    It will be less. Need to try.

    Leave a comment:


  • Rocco
    replied
    Dmitri, with bigger turbos like k24 7200 or k26/27 ,how many boost will produce in the launch control??

    Leave a comment:


  • Costash
    replied
    Can I sign in for the second kit?

    Leave a comment:

Working...