Lower door strips - RS2

[RS2junkie]

Hi,
I would prefer a paintable version, but would take either...

Thanks
P

[veneto rs2]

Its not regular double side tape, like you can buy in the store.
Its special hd 3m tape. I can give you the kg/m2, but it uses race car rear wings.
so dont worry about it.

Based on quality of Aron jobs and previous experience on dealing with him.
I trust him 100% on this.

Stefano

[madpugger]

I'd prefer paintable too.

The 3M tape I have rolls of here and it stick like **** to a blanket so I'd not worry there folks.

[kims2]

I NEED THIS BITS for me S2 Avant !!
is someone making them?!?!
pleas take contakt whit me On this mail! kimatull@hotmail.com
i am serious !! they are nowhere to finde in norway!!

Audi parts number:
8a0 853 991 b
8a0 853 992 b
893 853 959 b
893 853 960 b
893 853 969 b
893 853 970 b
8a0 853 699 a
8a0 853 700 a

[A80Avant]

I NEED THIS BITS for me S2 Avant !!
is someone making them?!?!
pleas take contakt whit me On this mail! kimatull@hotmail.com
i am serious !! they are nowhere to finde in norway!!

Audi parts number:
8a0 853 991 b
8a0 853 992 b
893 853 959 b
893 853 960 b
893 853 969 b
893 853 970 b
8a0 853 699 a
8a0 853 700 a

Aron is making the rs2 ones in carbon. So consider it an upgrade

[dhali7376]

keep m updated on this please. I would prefer the paintable ones but if those are not going to be produced i would be interested in the carbon ones.

[kevert]

Any news on these strips? I definetly need a set as I almost lost one today! Would prefer paintable ones.
Regards,
From Holland

[Louie C]

Sorry to be dumb but I assume they are the same as S2 Avant ones, if so then Id 100% be up for either

[kevert]

I just ordered all parts I required for my RS2 online in Germany. That is: all parts to replace the lower door strips, a brake pressure accumulator, the gear knob and the reflector plate between the back lights. Price was very good as I was entitled to a nice discount as registered workshop.

If anyone is interested please send me a pb and I'll give you details of the shop.

[handy andy]

i am thinking about to make a cheaper, non carbon , paintable version.
How it sounds?

Any updates on these yet

[handy andy]

Anyone?

[darkhorse1210]

Anyone?

Andy

I send Aron a monthly PM to check on progress and he's not yet fully happy with the moulds he has done, hopefully it will be soon.

Tom

[aronmatic2]

I have few prototypes, but i am not 100% happy with them. I need some extra time to finish it good. Sorry guys for the delay, but i dont want to try on anyones car. I have to finish it 100%, before i sell the first set.
the corners are fine, but i need to finish the doors.
We have lot of orders, so that is what we have to make first. After that, we car work on the new products, moldings.
I know, there is a lot of forum members, who need the trims. Its will be finished as soon as possible. this is the priority for me.

[Ross]

I signed up for Wab's group buy... Is this a continuation of it now, or is that still going on separately?

I have till about next summer till I need a set but cash is waiting when these become available, but I do want mine colour coded with the car so must be paintable! If not I'm waiting for one that is. I would prefer not to bend over and pay a grand for genuine ones that will rot again 5 years later!

[rs2315]

I signed up for Wab's group buy... Is this a continuation of it now, or is that still going on separately?

I have till about next summer till I need a set but cash is waiting when these become available, but I do want mine colour coded with the car so must be paintable! If not I'm waiting for one that is. I would prefer not to bend over and pay a grand for genuine ones that will rot again 5 years later!

Wab went to tim book 2 and he hasn't got back yet.

Best go with the carbon Ross.


rs2315.