Intake manifold porsche inscription

[Nuvo]

with the itallic 'sport' and all lower case powered by.

made the plate a bit smaller according to the recess measurement on my manifold.

That looks really good, is it possible to "open up" the Sport font like that before as it appears a little skinny or is this a consequence of scaling down the area of the plate?

[willg54]

That was a consequence of scaling it down. But my cad skills haven't been used up yet so I could be able to open it a little.

I wasc aiming to keep the capital a and s the same size height wise.

I'll play some more

[Nuvo]

I was aiming to keep the capital a and s the same size height wise.

I agree with that decision.

[willg54]

3rd try lucky!?

[willg54]

comparison of the last 2

[willg54]

looking at spec'ing the material.

my choice goes with
6082 - great for treatments (anodising etc), high anti-corrosion - most expensive but not outrageous
5251 - great corrosion resistance, typically found in marine applications - bit cheaper
1050 - cant heat treat it, good corrosion resistance and cheap!

and 2 or 3mm? trying to source 2.5

[Nuvo]

The opened lettering looks much better now.

[Big Lee M]

I'd like two of these's depending on price,would it be possible to have it without the red filling?

1. MadPugger - Audi Sport
2. MadPugger - Porsche
3. ALS2 - Audi Sport
4. quattrostyle
5. TimE-J - Audi Sport
6. vonbeck Audi sport
7. Dan - One of each
8. S2_WOT - Audi Sport
9. andy broke it - Either lol
10. bikerjim - Audi Sport (depending on price)[/quote]
11. jade - Audi Sport
12. HPmuirt - Audi Sport
13. Hoffer76 - Audi Sport
14. Willg54 - Audi Sport - cant forget myself!
15. Big Lee M - Audi Sport x2

[willg54]

I'd like two of these's depending on price,would it be possible to have it without the red filling?

I'll supply they as bare aluminium, no paint, no treatments etc so you can do what you like to make them individual.

As for cost, i think i'm working on around £20 +p&p "donation to my studies" to cover material, tooling, time programming etc and beer to fuel the technicians. Would you say this is reasonable?

[vonbeck]

I'll supply they as bare aluminium, no paint, no treatments etc so you can do what you like to make them individual.

As for cost, i think i'm working on around £20 +p&p "donation to my studies" to cover material, tooling, time programming etc and beer to fuel the technicians. Would you say this is reasonable?

i should coco

[als2]

Fine by me buddy! Crack on!!

[Rocco]

can i take one?? Audi Sport for me too

[willg54]

Of course, added you to the list!

1. MadPugger - Audi Sport
2. MadPugger - Porsche
3. ALS2 - Audi Sport
4. quattrostyle
5. TimE-J - Audi Sport
6. vonbeck Audi sport
7. Dan - One of each
8. S2_WOT - Audi Sport
9. andy broke it - Either lol
10. bikerjim - Audi Sport (depending on price)[/quote]
11. jade - Audi Sport
12. HPmuirt - Audi Sport
13. Hoffer76 - Audi Sport
14. Willg54 - Audi Sport - cant forget myself!
15. Big Lee M - Audi Sport x2
16. Rocco - Audi Sport

[madpugger]

Price sounds good to me mate, will throw in a donation to the beer fund on top

[willg54]

suggestion from shane, could someone measure the 'powered by' text height on an actual one if they have one??

hard to find one when its a thread about making them for people without them haha