Audi 80 b4 bordcomputer

[Skull]

Everything is the same, you only need new brackets (holders). The coupe has the same brackets as the s2.

on the rear is also everything the same, you only need side brackets (the the rear wheels) for the s2 bumper.

here in the pic you have 2 s2 rear bumper brackets, and one audi 80 bracket, so you see the difference:

[spyros80]

Competition bumper

I forgot to ask you, if the rear bumper's supports (on the chassis) are the same as mine or different like the front's?

[spyros80]

B4 bumper

Also, I would like to ask you if the front chassis of competition is the same with mine, as far as the installing of the front bumper is concerned. I mean the front part where the car's cooling system is situated. I believe that finding the plastic internal supports is ok. But, a different front chassis would be a problem.

[Skull]

Yes it is the right place. Try to change the sensor, maybe it is faulty.

[spyros80]

B4 Ata

I put it exactly behind the left bumper grill. I bought the original support and I screw it in the chassis in the left side behind the left bumper grill. Audi greece cannot tell me where Audi put this, as Audis with such an equipment have never been imported in Greece. So I have to guess and I put it there. I don't know if the hot air from the air ventilation passes to that way. But It is not rational, as the sensor looks straight to the fresh air. Any ideas?

[Skull]

Maybe it is the position of the sensor that is not ok. Where did you put it?

The internal supports of the front bumpers are not the same as yours, but the plastic behind the wheels is the same.

[spyros80]

Audi B4 ATA

Dear Skull,

I would like to ask you this: I connected the white/blue wire for the external temperature and it works fine. The only think I observe , after driving some, is that when I turn off the ignition and then turn it on again the gauge's indication goes straight to 55 degrees. Then it drops gradually until 46 and that's it. The right indication returns only if I stop the car for a half an hour or so. It is like erasing the car's memory when I turn off the engine. Do you know if this is a problem?

Also, Iam looking for Competition bumpers (front, rear). Do you know if the internal supports of the bumpers and the internal front plastic coating (behind the front wings)are the same as mine?

[spyros80]

B4 bc

Thank you very much again. You are my salvation! I' ve looking three weeks for that.
I want also to ask you if you have photos during the side skirt installation?

[Skull]

yes it is. the external temp meter needs the speedo signal, so it knows when the car is standing and at what speed it is going.

[spyros80]

audi 80 b4 bc

It is for the connection of the grey wire of the external temperature gauge. This wire is white/blue and it is in this plug. There is one cable with this colour in the blue 26 pin plug behind the speedometer. I just want to make sure that it is the same in order to connect the gauge. Any ideas?

[Skull]

i have no idea what that is. What is it needed for?

[spyros80]

Audi B4 Bc

Dear Skull,

One last question. Do you happen to know where is the black plug T10 (auxiliary services) or the sender G21?

Best Regards

[spyros80]

Bc Audi 80 B4

Thank you very much for your help I searched my car and i found the consumption wire too. In my car is yellow. You 've been very helpful. So, the only thing I have to pay attention to is to buy a BC with Auto/Check..
Thank you very much again.

[Skull]

all the BC are the same, even from the v6.

the large brown 6 pin connector is for the stalk stick, the black is connectord into the bc, the red one is not connected anywhere, and the yellow is the consumption signal.

[A80Avant]

skull,
spyros' car only has the usual Auto check that all B4 had,nothing more.In order to fit the board computer he has to also fit the stalk with the reset button.His main concern is where to connect each cable after he gets a complete kit,and from which year that kit should come from.
Also will that kit show the correct concumption if lets say it comes from an S2 or an audi V6?