Announcement

Collapse
No announcement yet.

Audi b4 80 2.3e FWD swap transmission

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Audi b4 80 2.3e FWD swap transmission

    Hello,
    The automatic transmission in my 1993 Audi b4 80 2.3e FWD went bad; So decided to replace with a manual transmission. I am taking out my 3 speed and replacing it with a 5spd fwd tranny. I was just wondering if the following part is what I need:
    1.drive axles
    2.gearbox w/mounts
    3.flywheel
    4.clutch pressureplate
    5.disk
    6.master and slave cylinder
    7.entire pedal assembly.

    Could somebody please let me know if I am missing any parts. Any thoughts or suggestions that you might have for me will be appreciated.

    Thanks for your support!
    GC
    Last edited by GarCo20; 18th January 2018, 10:10.

  • #2
    I found an Audi 100 with the same engine and manual transmission. Will this transmission fit in my car?

    Comment


    • #3
      Could somebody please let me know if I am missing any parts

      Comment


      • #4
        Yes. Gearbox will fit. You will have to remove the bushing from cracnkshaft to install flywheel.

        I threaded the bushing and screw in a bolt, and it popped right off.

        Maybe the 80 2.3 don't have the busing ang has a bearing instead.

        1989 Audi 80 Quattro
        1994 Audi 80 Quattro Competition

        Comment


        • #5
          M2ki,
          Thanks for your prompt response, your help is highly appreciated.

          Comment


          • #6
            Catalogue doesn't show any bearing or bushing for 93 80 2.3 automatic crankshaft, but can't be sure before you remove your old gearbox

            2.3 manual gearbox code should be AXG
            1989 Audi 80 Quattro
            1994 Audi 80 Quattro Competition

            Comment


            • #7
              I will remove my old gearbox next week. Do you know if the Audi 100 2.3e drive axles or the drive axles from the Audi 80 2.0 will work in car?

              Comment


              • #8
                Does anyone know which is the correct drive axle for my new transmission (code AXG). I am looking for the part number. Thanks!

                Comment


                • #9
                  8A0407272AT
                  right
                  108MM flange
                  Model data: NG,6A,ABB,ACE,ADA

                  8A0407271AT
                  left
                  108MM flange
                  Model data: NG,6A,ABB,ACE,ADA

                  New drive shafts can be pretty expensive and hard to find, buy used ones and replace CV joints.
                  1989 Audi 80 Quattro
                  1994 Audi 80 Quattro Competition

                  Comment


                  • #10
                    The 1.8T AEB automatic and the 2.8 AFC Automatic both had the bushing, even though the catalogue doesn't show it there's a good chance that your engine will.

                    Comment


                    • #11
                      Here are the parts that I have so far.
                      Attached Files

                      Comment


                      • #12
                        The new drive axles and the ECU are headed its way. The ECU came from Audi 80 2.3 with manual transmission. If somebody thinks I'm missing a part, please let me know. Thanks for your support!
                        Attached Files

                        Comment


                        • #13
                          I dont think you need a new ecu on car that is so old.
                          Left gearbox mount?
                          Does the manual gearbox clear the mount on the body for automatic gearbox?

                          Last edited by M2ki; 9th February 2018, 09:06.
                          1989 Audi 80 Quattro
                          1994 Audi 80 Quattro Competition

                          Comment


                          • #14
                            That is quattro subframe right there. B4 manual tranny usually needs just one gearbox mount on the subframe!

                            Comment


                            • #15
                              He can't use fwd subframe, because his car don't have the correct mount on the body. See pic and part nr. 3
                              He must use qauttro subframe and left quattro gearbox mount.

                              Auto box is secured from rear and mount is located in the cardan tunnel.

                              Lots of pics from auto->man swap http://www.motortuning-forum.de/boar...istungsupdate/


                              Last edited by M2ki; 9th February 2018, 09:24.
                              1989 Audi 80 Quattro
                              1994 Audi 80 Quattro Competition

                              Comment

                              Working...
                              X