Announcement

Collapse
No announcement yet.

Rear diff mount bush

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Rear diff mount bush

    Hello!

    I am going to replace bush for rear diff mount.
    I noticed that the new bush I bought is not centerd like the old
    one..

    So, what is the right way to press it in?



    //Emil


    Audi S2 Coupe -93
    Urquattro -83

  • #2
    Have no one replaced this one?
    and knows how it shold be?

    /Emil
    Audi S2 Coupe -93
    Urquattro -83

    Comment


    • #3
      I replaced mine with the same bush pictured. The knackered one removed had a centered hole.

      The subframe bolt hole was like a long kidney slot and i pressed it in as per the bottom right picture.

      Would be good to get some more answers on it.

      Comment


      • #4
        Thanks!

        Have totally missed that you can adjust on the subframe!
        made it a alot easier..

        /Emil



        Originally posted by Tony Stark View Post
        I replaced mine with the same bush pictured. The knackered one removed had a centered hole.

        The subframe bolt hole was like a long kidney slot and i pressed it in as per the bottom right picture.

        Would be good to get some more answers on it.
        Audi S2 Coupe -93
        Urquattro -83

        Comment


        • #5
          About to get one of these pressed in this afternoon, is the bottom right picture the correct orientation?

          Comment


          • #6
            Bottom left normally.

            There should be an arrow on the bush indicating direction of travel
            Mike

            http://www.s2-audi.co.uk

            Comment


            • #7
              Will do you have the part number for the new bush? I need one
              Panthero Coupé quattro 20vt
              Indigo ABY coupé
              Imola B6 S4 Avant

              Comment


              • #8
                Originally posted by Mikes2 View Post
                Bottom left normally.

                There should be an arrow on the bush indicating direction of travel
                Great, cheers for the info, there is an arrow on the bush as per the pics above so sorted. Thanks.

                I have a Febi Bilstein bush Alex, Part no. 06879.

                Comment


                • #9
                  Sweet cheers mate ��
                  Panthero Coupé quattro 20vt
                  Indigo ABY coupé
                  Imola B6 S4 Avant

                  Comment


                  • #10
                    Originally posted by Colesy View Post
                    Febi Bilstein bush Part no. 06879
                    Waste of time, it's too weak. Lasted one vacation in small mountains on my car.

                    Comment


                    • #11
                      I liked this better: Nissan 54476-10V02 (or replacements). It contingently fits coupe diff. Some mods needed.
                      Attached Files

                      Comment


                      • #12
                        I'm looking to replace this bush again as went from a Febi, which like you say is just to soft, to a powerflex which i'm not liking due to the increased vibration. Whats mods are needed to the Nissan one? Cheers

                        Comment


                        • #13
                          Needs a sleeve putting in I believe. I have one here but not got around to it yet
                          Panthero Coupé quattro 20vt
                          Indigo ABY coupé
                          Imola B6 S4 Avant

                          Comment


                          • #14
                            Hey. A sleeve between the bolt and the inner bonded bush? I wonder has anyone drilled more holes in the powerflex bush to soften it up a bit. Might try that to see how it works out.

                            Comment


                            • #15
                              Originally posted by gmac78 View Post
                              Whats mods are needed to the Nissan one?
                              Diameters difference is very small. I put a small drop of welding onto the bushing sleeve so that it would fit tight into the mount.

                              Comment

                              Working...
                              X