You can change the style the forum displays by selecting your preferred style at the bottom left of the site.
We have made an enhancement so that old threads should now link from search results to the correct thread. This is not yet in place for single post links
Albert received mine this week. Great products as
usual! Any chance you have a preferred place to
buy the hardware for these or can you supply the
hardware?
Working to install the caster mounts & have a question. Do the bushings from Albert need to be split to install over anti roll bar or do I need to use a little more muscle?
Working to install the caster mounts & have a question. Do the bushings from Albert need to be split to install over anti roll bar or do I need to use a little more muscle?
Sorted. I did not split the bushing. Just needed to get midevil on it's butt.
Did mine today, got the bolt suggested by Abert and they fit fine. The brackets also fit fine. Make sure they are both fitted the correct around
Doesn't appear to need to be tracked.
Ghetto comment, on full lock the inside wheel leans over a bit like a Merc wheel, and the outside one appears a bit more upright on full lock. Too too soon check any improvement to handling as only drove it around the block. Dark and even colder when I finished a 8pm after starting a 12.00pm. (Changed the oil as well).
The bushes were levered into position on the FARB by placing it in a slightly open bench vice and lift the bar up or down depending on which end was being fitted. There is no need to cut them. Grease the inside of the bush with the clear grease provided by Albert. Clean the anti roll bard well first to allow you to slide on the two bushes from each respective end and also so as the grease is not contaminated unnecessarily.
Will be driving it this week so that will tell a story.
Wheels do sit further forward in the front wheel arch on side profile. Is not noticeable except by the likes of me.
Like anything to do with C4 front suspension, it is hard tiring work on a wet gravel driveway with axle stands and trolley jacks. No fault of the brackets though, thanks for making them.
My S8 Mk1 255/35/18 not longer rub on the rear arch on full lock. Now just need to replace both wheels arch lines as they have been rubbed away by the tyres.
Did mine today, got the bolt suggested by Abert and they fit fine. The brackets also fit fine. Make sure they are both fitted the correct around
Doesn't appear to need to be tracked.
Ghetto comment, on full lock the inside wheel leans over a bit like a Merc wheel, and the outside one appears a bit more upright on full lock. Too too soon check any improvement to handling as only drove it around the block. Dark and even colder when I finished a 8pm after starting a 12.00pm. (Changed the oil as well).
The bushes were levered into position on the FARB by placing it in a slightly open bench vice and lift the bar up or down depending on which end was being fitted. There is no need to cut them. Grease the inside of the bush with the clear grease provided by Albert. Clean the anti roll bard well first to allow you to slide on the two bushes from each respective end and also so as the grease is not contaminated unnecessarily.
Will be driving it this week so that will tell a story.
Wheels do sit further forward in the front wheel arch on side profile. Is not noticeable except by the likes of me.
Like anything to do with C4 front suspension, it is hard tiring work on a wet gravel driveway with axle stands and trolley jacks. No fault of the brackets though, thanks for making them.
My S8 Mk1 255/35/18 not longer rub on the rear arch on full lock. Now just need to replace both wheels arch lines as they have been rubbed away by the tyres.
Hope this feedback helps other C4 owners.
Cool. Any pictures of them installed. Are the wheelarch linersstill available. non s cars are not the same....
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
looking forward to hearing how it drives this coming week.
Comment