Announcement

Collapse
No announcement yet.

Group buy: Adapter for fuel pressure sensor with oel connecter

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Group buy: Adapter for fuel pressure sensor with oel connecter

    So I'm looking to get this little adapter made.



    It will be male M14x1,5 with flared end and female M14x1,5 designed for the Audi connector.

    It will then have a threaded 1/8" npt hole for sensor etc. This thread in the hole can be changed to something else.

    It based on the German DIN standards for a Bördel F connector which Audi uses for our cars.

    Plan is to make it in Alu and stainless steel (if it won't be to expensive) and it will be fitted like this.




    I trying to get a quote and I would like to have 10-20 made to get the price down.

    I will update when I get some prices.

    Update 15-06-2017
    Prototype ordered 15-06-2017, should hopefully have within 1-2 weeks.

    Price Update 21-07-2017
    Price in stainless steel minimum of 10 units: 45 euro + shipping.

    We have dropped the aluminium part.

    Hoping to start collecting money in week 30-31 and then start the prototypen in week 32.

    Installation instructions:

    I install my fitting in the fuel feed line, at the junktion near firewall.

    If you have problems getting the sensor to orient the right way, then you can loosen the feed line at the fuel rail and get the fitting and sensor oriented correct and then thigten the feed line afterwards at the fuel rail.

    For the fitting itself there is no need for thread sealent.

    However the sensor should get some thread sealent or PTFE tape or similar.

    Installed on my ABY:
    IMG_20180307_202647858.jpg

    IMG_20180307_202623692.jpg
    IMG_20180307_202645445.jpg
    Last edited by Jonas_R; 3 June 2018, 15:12.
    Sleeper S2 Avant +450

    A6 Avant 2.7t Stage 3

    Audi S2 Coupe RS2'ed

  • #2
    I want one, two if it helps to get it done
    Really appreciate your work Jonas

    Comment


    • #3
      1x Jomas_R
      1(2)x s0_big
      Sleeper S2 Avant +450

      A6 Avant 2.7t Stage 3

      Audi S2 Coupe RS2'ed

      Comment


      • #4
        Originally posted by Jonas_R View Post
        1x Jomas_R
        1(2)x s0_big
        Nobody else that are interested in this nice part? ☺

        Comment


        • #5
          Yeah, go on then, add newsh to the list [emoji106]

          S2 Coupe 3B Project


          Ur quattro restoration

          S2 Avant

          Boost is the new rock and roll!
          sigpic

          Comment


          • #6
            1x Jonas_R
            1(2)x s0_big
            1x newsh
            Sleeper S2 Avant +450

            A6 Avant 2.7t Stage 3

            Audi S2 Coupe RS2'ed

            Comment


            • #7
              Just a quick update. I have quotes out at two vendors.

              I have asked for prices in Alu and stainless steel.

              I'm dropping the brass idea.
              Sleeper S2 Avant +450

              A6 Avant 2.7t Stage 3

              Audi S2 Coupe RS2'ed

              Comment


              • #8
                Hi, I'm interested too
                photobucket SUCKS
                sigpic

                Comment


                • #9
                  I have interest on it but to be perfect is better we find a fuel pressure sensor and put on adapter. Will be perfect to send information to standalone ecu about pressure in fuel system.
                  .: Audi Coupe Quattro 20V 91' :.
                  .: Audi/PorscheRS2 95' :.
                  .: Mitsubishi 3000GT VR-4 96' :.

                  Comment


                  • #10
                    Zeitronix Sells a 10 bar fuel pressure sensor that I'm planning to use.

                    I'm not planning to include sensor, since people use different logging equipment, ECU etc.
                    Sleeper S2 Avant +450

                    A6 Avant 2.7t Stage 3

                    Audi S2 Coupe RS2'ed

                    Comment


                    • #11
                      Great idea, I want to order two of these adapters.

                      Regards Eivind.

                      Comment


                      • #12
                        Since I have Maxxecu I will connect this sensor to my Ecu.

                        http://www.maxxtuning.eu/products/en...gas-or-ethanol
                        Last edited by s0_big; 22 May 2017, 18:51.

                        Comment


                        • #13
                          1x Jonas_R
                          1(2)x s0_big
                          1x newsh
                          1x M_Gordon
                          2x Dynasty
                          Sleeper S2 Avant +450

                          A6 Avant 2.7t Stage 3

                          Audi S2 Coupe RS2'ed

                          Comment


                          • #14
                            Originally posted by Jonas_R View Post
                            Zeitronix Sells a 10 bar fuel pressure sensor that I'm planning to use.

                            I'm not planning to include sensor, since people use different logging equipment, ECU etc.
                            Yes report me please if you can do by this way. If i can use Zeitronix sensor in your adaptor i have interest in 1 unit.
                            .: Audi Coupe Quattro 20V 91' :.
                            .: Audi/PorscheRS2 95' :.
                            .: Mitsubishi 3000GT VR-4 96' :.

                            Comment


                            • #15
                              Originally posted by Nuno_Cristiano View Post
                              Yes report me please if you can do by this way. If i can use Zeitronix sensor in your adaptor i have interest in 1 unit.

                              Most sensors use 1/8 NPT thread, and thats what Jonas was thinking (i think) to use as "standard" for the sensor thread on the adapter.


                              "It will be male M14x1,5 with flared end and female M14x1,5 designed for the Audi connector.

                              It will then have a threaded 1/8" npt hole for sensor etc. This thread in the hole can be changed to something else.

                              It based on the German DIN standards for a Bördel F connector which Audi uses for our cars.
                              "

                              Comment

                              Working...
                              X