80Q Competition 20VT inside¡¡

[Rocco]

altitude sensor? are you going to be doing any hill climbs or drive on the mountains at full boost??

No,it is only a street car and yes I took your taunt . It is a gay boost with gay timing but it is only for drive carefully while I am testing every seal,bolt,nut or fluid leaks after the huge job

We will see the knock limit with the 8.0:1 CR

[A80Avant]

Simplicity is always good. Overcomplicated things sometimes makes the car spend more time in the garage, looking for boost leaks, limp modes etc.

Safe and simple is my moto!

Color wise, i would paint it a dark blue, like Anders avant and then if i got bored, i would use vinyl cover to change the color on top!

[Rocco]

RS2 limo in Daytona Grey. I can't decide between this and full black for my UrS6.

Have you tried the "google for random pictures until you find the car colours that look interesting" solution?

Yes I have Googled lot of times ,with images also.
And with Audi 80 there are not many different results.

It's a hard decision.daytona grey looks pretty but I am not sure about nothing.

Black colours are nice but not very friendly with the dust

What do you think about the " duck blue egg colour"? it is one Audi oem colour... I have not seen any car like this.

Pearl white its surelly one of the best but since I have the coupe.... 2 old/iron cars with the same colour will looks sick

[quattrostyle]

You must paint it Daytona grey mate, really the best colour once you've seen it IRL and doesn't show dirt on the paint as well as other colours

[Zoig]

Do you know the official colour name or code for this blue one?

[Rocco]

You must paint it Daytona grey mate, really the best colour once you've seen it IRL and doesn't show dirt on the paint as well as other colours

yes it is a good candidate it that colour the car will looks awesome with smoked tail lights ,RS2 rear bumper and tint a RS2 rear panel reflector

Do you know the official colour name or code for this blue one?

i am going to check for it

[quattrostyle]

You'll have to make the decision yourself eventually. If you are considering Daytona then please go and see it on a car IRL it will convince you.

[Rocco]

here a picture of my "home-made" air intake sistem...ready to work with Motronic and tubular exhaust manifold and MAF in the non pressuriced side ,ready for tuning the tiny turbo

[Rocco]

also,do you know guys if there is an easy way to know if the exhaust manifold are K26 o T3 flanged?

because i would like to know it without uninstall the turbo of course

i believe to listen my friend Vadim "Sweeper" member that it is a k26 flange .... but i am not complete sure..i would have to do some meassures in the bolting place...or maybe it is a waste of time

anyway ATM it is not too important


thanks¡

[Jamo]

Depends on the flange t3 are flat rectangle kkk tend to have curve in the middle of the flange because of the circular output

[A80Avant]

that engine needs tidying up!

[Rocco]

Depends on the flange t3 are flat rectangle kkk tend to have curve in the middle of the flange because of the circular output

yes i understand you,but now there is not too many room to check

that engine needs tidying up!

Vasilis, first of all i want it running perfect and it is a waste of time to clean and tidy it... because always i am with the hands dirty touching everything... and after all,a dirty engine runs always the same or better than a cleaned one....sometimes the people has problems with the ignition sistem after wash the engine bay,so this is not my problem now

but i would accept you if you want to lend me a hand with it

[A80Avant]

I didn't mean to wash it !
If you pop along in the UK again, why not!
sent using Android

[Rocco]

I didn't mean to wash it !
If you pop along in the UK again, why not!
sent using Android

yes but tidy also... i need to finish much more things yet


i have said it because some stupid people in Spain told me " please wash this engine bay" and i answered them "No thanks,it is just fine like this"

[sailaz]

i dont like too much this brake part... not sure if it will be enough or not...and i will look if the S2 3B it is a easy bolt on replacement , and this brake dont use the problematic brake ball

here how it looks in mine

before

after; brake servo from A8/S8 D2; brake bomb is gone as well.