You can change the style the forum displays by selecting your preferred style at the bottom left of the site.
We have made an enhancement so that old threads should now link from search results to the correct thread. This is not yet in place for single post links
Less inertia is nice for sure. Is it a direct replacement in terms of trim or is it designed for higher / lower flow? I ran a k24 7000 billet hybrid for a bit and spool was very fast and it sucked air in like a beehatch
Cheers'en, AndyC
1994 ABY Coupe - Projekt Alpinweiss
direct replacement in the sense that it fits the stock turbo and housing, however it is a 10 blade compressor designed for better/more flow, also is like 40% lighter then the oem wheel. this is the first one going out so it is still being proven.
For me It will flow and spool better but I don't think the bhp levels will raise that much
Would need bigger turbine / housing for that IMO
How much is that wheel and how was the balancing?
Lol easy Solidworks design with just a single loft, cut revovle and some fillets!
I like the idea of billet replacements as a solution for the future, not sure about the efficiency though.
Lol easy Solidworks design with just a single loft, cut revovle and some fillets!
I like the idea of billet replacements as a solution for the future, not sure about the efficiency though.
Nice snarky posting...I'm not sure what your point is.
There is a wee bit more to engineering than modeling parts. Sure, that is a relatively simple model, but I do believe there was a radial pattern required too that you missed.
What about choosing the proper material, optimizing inducer and exducer sizes/trim, implementing extended tip geometry, reducing rotational inertia, flow analysis, and of course actual testing. These have been pretty thought out.
If you like the idea of billet replacements in the future, why not believe they can be done in the present? The efficiency can at least be improved from what RS2 was capable of.
"The overall weight is around 46g compared to 62g for the rs2 wheel. Now the comp wheel is attached to a shaft, bearings and another turbine wheel that weighs significantly more than the compressor wheel. In the end of the day it is only a 6-7% reduction in overall inertia moment, put the aero is what is really what will help. CAD modeling and flow analysis show it will be good for around 36lbs/min, or roughly 360whp really pushed at around 2.5 bar. We will see "
I am still not sure if the Garrett GTX design is the best for an Impeller. Looking at the new Holset and BorgWarner wheels they still have secondary blades.
I certainly think it's worth the research if someone is willing to put in the time... as Hoffer has proved, you can make a frankenturbo to good effect when the balance is right. What I like about this is there's no machining involved, just fit and balance so cost is minimal. It'll be interesting to see how the figures come out.
As Jamo pointed out, I would expect the turbine to become the bottleneck here, but peak flow isn't the only characteristic that can be changed. Better response and +10-20hp would be a pretty good upgrade though, especially if it avoids writing the turbo off!
Nice snarky posting...I'm not sure what your point is.
There is a wee bit more to engineering than modeling parts. Sure, that is a relatively simple model, but I do believe there was a radial pattern required too that you missed.
What about choosing the proper material, optimizing inducer and exducer sizes/trim, implementing extended tip geometry, reducing rotational inertia, flow analysis, and of course actual testing. These have been pretty thought out.
If you like the idea of billet replacements in the future, why not believe they can be done in the present? The efficiency can at least be improved from what RS2 was capable of.
My point being that this makes it look quite easy to develop an impeller from scratch, while it takes the OEM's years to gain 1% in efficiency through unlimited resources.
Latest and greatest achievements are recently found through coatings, which you need if you go billet to reduce abrasive wear by the elements.
As for the replacements, sure it's doable in the present and i like the motivation of those guys to even do all this work for such a small niece market. Not directly convinced of the benefits in terms of efficiency though.
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment