went to order mfts today, and found that there are new part number, wasnt ordering of audi, but a good german parts supplier, 035919 369 L , 4 pin MFTS, far i as i know the new one has three pins, am i still good ?
-
1991 S2 3B Coupe, KW v1, solid sub frames, poly bushed, chipped, about 260 ish
-
The 035919369L was dropped on Aug. 31, 1992 in favour of a 046919369, i.e. 20 years ago. In turn the, 046919369 was dropped on Dec. 31, 1993 in favour of the three pin 034919369C. This is the part number you want to use.
RS2'd 93 UrS4 5 spd sedan
94 UrS4 V8 6 spd manual avant -
Thank you. i have it ordered as well as other sensor in 3b water manifold for good measure.. will double check part # at store counter when i collect. thanks againThe 035919369L was dropped on Aug. 31, 1992 in favour of a 046919369, i.e. 20 years ago. In turn the, 046919369 was dropped on Dec. 31, 1993 in favour of the three pin 034919369C. This is the part number you want to use.
1991 S2 3B Coupe, KW v1, solid sub frames, poly bushed, chipped, about 260 ishComment
-
Like the Thermal Switch that activates the After-run pump?
RS2'd 93 UrS4 5 spd sedan
94 UrS4 V8 6 spd manual avantComment
-
yes thats the one, to the left of the MFTS.1991 S2 3B Coupe, KW v1, solid sub frames, poly bushed, chipped, about 260 ishComment
-
Hello
Up this thread because i ve ordered the 3 pins one for my 3b
But after installed it my water temp goes over the normal temp without starting the fan on ...
Is there a trick to check the new sensor ?
I ve put back the old 4 pins one and it's back to normal operation
:what:91' S2 3B Pearl WhiteComment
-
Fan runs from the otter switch in the bottom of the radiator, not from MFTS.
MFTS has several jobs according to the book..
Reduce boost pressure when temp is over 119degC
Coolant temp indication.
Engine temp warning
Climate control.Comment
-
Ah, just read again, so what you're saying is the temp gauge is over-reading?Comment
-
Maybe an intermittent short in the wiring plug?Comment
-
Yes over the 2 lines after 90° with the new one and no fan
With old one everytime it reach the second line after 90° fan starts91' S2 3B Pearl WhiteComment
-
If its a miele made one,they seems to be a general concensus that they over-read massively.Had this problem myself,swapped back to a behr one and normal temp reading.Rob
Ragussa green avant RS2+ spec
Racing blue Octavia VRS mk2 estate-Remapped now to 250 bhp
Audi coupe gt-slow as hell but loads of character-sold
Comment
-
More than likely not bled the system properly, or you have a small leak - maybe the cap.Cheers'en, AndyC
1994 ABY Coupe - Projekt AlpinweissComment
-
Need one of these too, was the cause of my boost issues… Where's the best place to get a new Behr one then?
Cheers
RussOld Stuff Reborn.Comment
-
I had a brand new 3 pin one that also over read.Current-2004 Impreza PPP wagon
Sold-92 3B coupe-RS2+, 996s, konis, rear torsen, forged rods........
Sold ABY-stockComment
-
Ok guys thx for feedbacks
I 'll keep the old one
91' S2 3B Pearl WhiteComment
Comment