rs2 engine problem!(help)

[A80Avant]

Umit has some good experience on vems. He should be able to help

[fatiii]

At last my friends my car started to work properly i thank all of you whom tried to help me.after a long time period, to drive this car is an excellent happines for me. From now on i will give all the details while i improve the condition of the car.i am sure with your help i am going to make this car better. S2forum family and my mapper remaps.tr umit dogan please accept my special thanks

[A80Avant]

Log files are too small to get any meaningful conclusions

[Nuno Cristiano]

The only way to find out is to make sure the car has an ecu that is properly configured and doesn't have all those config validation errors. Only then you can say its the crank sensor

See log files of user

[A80Avant]

The only way to find out is to make sure the car has an ecu that is properly configured and doesn't have all those config validation errors. Only then you can say its the crank sensor

[Nuno Cristiano]

I had a look at the config and I must say that it must be a combination of things. The basic settings seem ok but the maps are decently horrible.

You need to upgrade the firmware to the at least stable 1.1.95 and make sure you use a strobe light to check the timing angle that it corresponds to vems. Then I have made some changes to the map but I have sent an email to find out some info for the engine specs before I continue.

Whoever decides to go vems they MUST get involved and not rely on a tuner who knows generic stuff. Whoever put values on this map either wasn't interested in the car or didn't know a lot of info. Please read about what you can do and we will try and help you as much as possible.

The crank sensor needs to be as close as possible without fouling the pins. If it still doesn't work then you need to weld a larger pin by copying the size and length of the original dual mass flywheel pin

I also got the config file and not by what is done there that the car will have that problem. If you look good is constantly trigger errors. Any problem with VR sensors.

The tables must be done correctly, but I repeat that what is there, must work properly and do not turn off the car as it appears in the video.

[A80Avant]

I had a look at the config and I must say that it must be a combination of things. The basic settings seem ok but the maps are decently horrible.

You need to upgrade the firmware to the at least stable 1.1.95 and make sure you use a strobe light to check the timing angle that it corresponds to vems. Then I have made some changes to the map but I have sent an email to find out some info for the engine specs before I continue.

Whoever decides to go vems they MUST get involved and not rely on a tuner who knows generic stuff. Whoever put values on this map either wasn't interested in the car or didn't know a lot of info. Please read about what you can do and we will try and help you as much as possible.

The crank sensor needs to be as close as possible without fouling the pins. If it still doesn't work then you need to weld a larger pin by copying the size and length of the original dual mass flywheel pin

[UrS4boy]

I must learn how to convert PDF's to JPG's

[UrS4boy]

G4 crank position and G28 engine speed sender info

this curvature is a normal?

Have a look at the photo below and read this post:

http://forums.quattroworld.com/s4s6/msgs/20986.phtml

Your's seem not so long compared to these. (see my other post re: distances)

[AndyP]

I must learn how to convert PDF's to JPG's

[fatiii]

thank you so much

[AndyP]

any idea?

The sensor on the flywheel teeth is 0.5-1.25mm. The one that picks up on the small single pin is 0.45-1.25mm.

[UrS4boy]

Detailed Crank Position Pin Info

how long distance have been between volant tooths and sensor

Have a look at the diagram below and read this post:

http://forums.quattroworld.com/s4s6/msgs/51259.phtml

[fatiii]

how long distance have been between volant tooths and sensor

any idea?

[stocious]

Hey fattiii, your car is sweet, it's yours, all that matters !!! Best luck getting it going !! Won't matter what's stamped on engine when I fires up one mans junk is another mans treasure !! I have 3 b too