Originally posted by Vorsprung durch Technik
View Post
Announcement
Collapse
No announcement yet.
My URS6 Plus Speck Saloon
Collapse
X
-
Fingers crossed i've got some time to get on with this.
I can't seam to find the part numbers for the inlet and exhaust studs i need. I need standard for the AAN IM but will need the shorter exhaust stud for the wagner manifold i believe manifold pictured below. Any suggestions on spec,type and where's best to buy them? Cheers.
96 URS6 plus speck saloon
96 URS6 plus speck estate
94 2.6 80 Avant
99 2.8 final edition Cabriolet
Comment
-
You can use normal 20v studs and shorten as needed although IIRC the Wagner doesn't actually need short ones? I know the Wagner was way easier to fit than the RS2 manifold, all the nuts are much easier to get to.
Comment
-
IM fits with allen bolts, you can re-use them.
Comment
-
23 N 90355902 socket head bolt with hexagon socket head (combination) M8X30
25 N 0147135 socket head bolt with hexagon socket head M8X35
Dave has a load of info on the exhaust manifold studs here
http://forums.quattroworld.com/s4s6/msgs/196904.phtmlCurrent-2004 Impreza PPP wagon
Sold-92 3B coupe-RS2+, 996s, konis, rear torsen, forged rods........
Sold ABY-stock
Comment
-
Just a wee update, she has a new mot certificate a couple weeks ago so very pleased after too long a lay up and before any bright spark checks the mot history it's actually a little out! Ive covered 116 since the last MOT and not the 16 he's put down.
Decided to completely rebuild the rear brakes so it matches the newly rebuilt subframes and suspension to come. Callipers were sent of the Big Red for the Luxury rebuild. Discs didn't come like that so sprayed them with what Halfrauds call Very High Temperature Paint which works very well so far. It's so nice to have a perfect handbrake again only 3 clicks to fully tight. Happy days.
fullsizeoutput_f8b_zpshw0jfhbx.jpeg
P1070370_zpskilbfvp8.jpg?776.jpg
Wheels all washed clayed and polished up.
P1070372_zpssvifguzs.jpg?591.jpg
I'm loving driving her again to be honest.
96 URS6 plus speck saloon
96 URS6 plus speck estate
94 2.6 80 Avant
99 2.8 final edition Cabriolet
Comment
-
Bit of an update. Due to the way the front of the car was looking due to a terrible previous paint job that had deteriorated further by crazing on the front wing tops i had no choice but to bite the bullet and get the bad bits rectified which were as it stood the whole front of the car and the rear bumper. This quickly once i was in the painters company up in Birmingham turned into, from me, exploring about getting the whole car done. Although the rest of the car looked good from 10ft away, every panel had some sort of paint chip, scratch or as in the case of the boot lid leading rear edge a nice little annoying dent. These defects bothered me so the decision was taken to paint the whole car except the roof.That will be done later with the extra paint they've mixed as part of the whole batch so i'll get a perfect match.
So,.........I received these pics from the painters. Some bumper rectification due to the spider cracks in the paint.
Resized_20180212_182736_zpsouxwnpky.jpeg?793.jpgResized_20180212_182803_zps8fpl6uzh.jpeg?581.jpg
Old wings of ready for new.
2018-03-27-PHOTO-00000009_zpsfbot3xbg.jpg
fullsizeoutput_114d_zpsjrk6urol.jpeg?t=1522106189?846.jpg
fullsizeoutput_1153_zpsibereyty.jpg
fullsizeoutput_1154_zpskl4zo7du.jpg
That's it for now unless i get anymore photos from them. The cars being flatted and polished ready for the refit of window frames trim etc etc and i should be able to pick her up in 9 days time fingers crossed.
Last edited by Vorsprung durch Technik; 28 March 2018, 00:33.96 URS6 plus speck saloon
96 URS6 plus speck estate
94 2.6 80 Avant
99 2.8 final edition Cabriolet
- 1 like
Comment
Comment