Announcement

Collapse
No announcement yet.

LarsSkogstad - Audi S2 (3B) 1991 Coupe

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Been grinding down inside wheel arches front. Thinking about getting a car rotisserie and take the whole car under, its not in that bad shape but I feel like it needs to be done
    You do not have permission to view this gallery.
    This gallery has 8 photos.
    https://www.s2forum.com/forum/member...-3b-1991-coupe

    Comment


    • Originally posted by larsaskogstad View Post
      Screenshot_20210217_101826_com.android.gallery3d.jpg

      Not recommended probably but works for me
      Do You still run with this "mod" ?
      Dunno if it's critical but it should be a 1k resistance between center and outer contact-point.

      Comment


      • Originally posted by pfi View Post

        Do You still run with this "mod" ?
        Dunno if it's critical but it should be a 1k resistance between center and outer contact-point.
        Yes, the mod is still there but not might be there. Is it a problem to run with it?
        https://www.s2forum.com/forum/member...-3b-1991-coupe

        Comment


        • don't know if it's a problem but measured mine and all have approx 1k "internal" resistance, guess it is there for a reason ?

          Comment


          • Originally posted by pfi View Post
            don't know if it's a problem but measured mine and all have approx 1k "internal" resistance, guess it is there for a reason ?

            Read somehwere it was there earlier to not interfer with AM radio frequencies but im not sure why, Ive seen rotors with or without.
            But I might go coil on plug solution anyway. havent had any problems running with this rotor, its been exceptionally smooth on everything (but of course everything is changed out so comparing this to some old car Ive had isnt correct either). Only had a s4 2.2t earlier with lots of ignition problems, but this car was utter trash

            https://www.s2forum.com/forum/member...-3b-1991-coupe

            Comment


            • 263759990_330030848622770_3192792460169258619_n.jpg

              The car looks like this at the moment so it's gonna be a while before it's on the road again
              https://www.s2forum.com/forum/member...-3b-1991-coupe

              Comment


              • Originally posted by larsaskogstad View Post


                Read somehwere it was there earlier to not interfer with AM radio frequencies but im not sure why, Ive seen rotors with or without.
                But I might go coil on plug solution anyway. havent had any problems running with this rotor, its been exceptionally smooth on everything (but of course everything is changed out so comparing this to some old car Ive had isnt correct either). Only had a s4 2.2t earlier with lots of ignition problems, but this car was utter trash
                Yea, propably works ok, guess You don't listen to AM these days ...

                Thinking of coil on plug myself, do You have part# for "plugs"​/connectors needed ?

                Comment


                • Think I will run it with maxxecu or ecumaster. The typical TFSI / or Audi R8 stuff. Think it works fine, coils are quite cheap as well if they break down.
                  Not too fan of having coils on top of the engine due to heat and vibrations, would rather have coils stacked in the rear as people used to do.. but I guess it works fine
                  https://www.s2forum.com/forum/member...-3b-1991-coupe

                  Comment


                  • Isn't TFSI coils "on top" ok if using 7A or 3B valve cover ? AAN with cover will probably "boil"'em ...
                    with coil's stacked in the rear is propably LS1(/LS2) coils ? got a set of those on a S4 I'm going to part and probably use them on a later project

                    Comment


                    • I ran the LS1/LS2 coils on my s4, it was quite nice solution.
                      https://www.s2forum.com/forum/member...-3b-1991-coupe

                      Comment


                      • Originally posted by larsaskogstad View Post
                        Think I will run it with maxxecu or ecumaster. The typical TFSI / or Audi R8 stuff. Think it works fine, coils are quite cheap as well if they break down.
                        Not too fan of having coils on top of the engine due to heat and vibrations, would rather have coils stacked in the rear as people used to do.. but I guess it works fine
                        On my 3B I use 034 high output coils mounted on the strut brace, means I get to keep the 3B cam cover

                        S2 Coupe 3B Project


                        Ur quattro restoration

                        S2 Avant

                        Boost is the new rock and roll!
                        sigpic

                        Comment


                        • do you have any pics?
                          wondering if it was the same solution I had on my s4 2.2t, bought it from 034 but its like 10 years ago.. time flies
                          https://www.s2forum.com/forum/member...-3b-1991-coupe

                          Comment


                          • Originally posted by larsaskogstad View Post
                            do you have any pics?
                            wondering if it was the same solution I had on my s4 2.2t, bought it from 034 but its like 10 years ago.. time flies
                            Couple of different arrangements



                            S2 Coupe 3B Project


                            Ur quattro restoration

                            S2 Avant

                            Boost is the new rock and roll!
                            sigpic

                            Comment


                            • Yeah this is the better way in my opinion, looks a bit similar to the ones I used to have.
                              https://www.s2forum.com/forum/member...-3b-1991-coupe

                              Comment


                              • Lars, will you remind those Bentley publishers? I think that they will have nothing more to say, but maybe it work out with that bentley manual. Thanks
                                Audi Coupe Quattro 2.3 20V

                                Comment

                                Working...
                                X