Hydraulic to Vaccum servo conversion

Collapse
This is a sticky topic.
X
X
 
  • Time
  • Show
Clear All
new posts

  • krzysztofkabaj
    replied
    I see . There's no such issue in C4 chassis. Only problem with dual diaphragm servo U need to solve is brake pedal rod. In C6/D3 we get ball joint, U need to cut it some longer piece of rod, make new M8 thread and use C4's original "fork" joint.
    I did not said the mod was easy but certainly was worth it.

    Leave a comment:


  • Error404
    replied
    Because the hole in the bulkhead is bigger on the C4 than B3/B4 chassis. The later dual diaphragm servo from the C6/D3 does not fit the smaller B3/B4 chassis without some modifications. You need to cut the bulkhead & modify the pedal box.

    Leave a comment:


  • krzysztofkabaj
    replied
    Yep, S6 C4. Why asking ?.

    Leave a comment:


  • Error404
    replied
    That is on a C4?

    Leave a comment:


  • krzysztofkabaj
    replied
    I'll add something from me. I converted hydro assist to C6 master cylinder, 8" booster and electric vacuum pump, exactly as in C6.





    Sorry for Polish marking on pics, they were made for use on PL forums .

    For control of electric pump was built control unit using old map sensor taken out of Motronic ECU .

    Leave a comment:


  • RS2
    replied
    I use a 7A in my VW T3 Transporter Tristar Syncro.

    It uses the vacuum servo, no problem. It has more than enough vacuum for the braking system.

    MG

    Leave a comment:


  • mihai_antony
    replied
    Hello

    I have an 2,3 7A 20v audi, FWD, and I want to make the conversion to vacuum brake
    It is better to use the parts from the 2,3 NG engine or the A4 B5 1.8T? The 7A produce enough vacuum for this conversion?

    Thank you very much!

    Leave a comment:


  • A80Avant
    replied
    Will these stick eventually like the rest of the forge valves?

    Leave a comment:


  • AndyP
    replied
    For reference Forge are now making a billet one way valve specifically for high boosting cars with vacuum brakes:-

    http://www.ebay.co.uk/itm/331470792631

    Leave a comment:


  • Error404
    replied
    058905291k

    Leave a comment:


  • AndyP
    replied
    Originally posted by Error404
    I have two check valves inline on mine as insurance against boosting the servo. One is the OE check valve the second one is ff a TT - I figured that would be designed to take boost.
    Do you have a part number for the TT valve?

    Leave a comment:


  • sailaz
    replied
    Originally posted by Ryss
    Here are the pics of the A8 and A4 B6 boosters.
    A4 fits. A8 does not fit thru attachment plate and therefore pedal set, as the nose piece dia is too big. Also note length from firewall to end of master cyl, is shorter on the A4 unit.
    In my RS2 I have fitted the double one from A8 D2 (4.2) without any problems ....

    Leave a comment:


  • popdemonic
    replied
    I had a black one way valve from VAG cars but not sure if it was taken from B5.working flawlessly just make sure you
    plumbed her on the correct direction.I remember the check valve has a 2 small nipples available for another system that required the vacuum soruce as well.i just plugged them off.

    Leave a comment:


  • A80Avant
    replied
    In my retrofit we used a one way valve from a Citroën which seems very robust. It's been a while I opened the hood of the car to check the valve but I will check and see if I can find a part number.

    Leave a comment:


  • Error404
    replied
    A couple of things you can check - pull the vacuum line off the servo and hold your thumb over it, start engine. You should feel a good vacuum on it. Switch off engine. It should hold vacuum for a while - if not the check valve leaks. If it does I am sure boost will not be doing the servo any favours!
    Also check the seal between the master cylinder and the servo. A brake fluid leak can damage the seals and get inside and also damage the diaphragm.

    I have two check valves inline on mine as insurance against boosting the servo. One is the OE check valve the second one is ff a TT - I figured that would be designed to take boost.

    Leave a comment:

Working...