Hydraulic to Vaccum servo conversion

Collapse
This is a sticky topic.
X
X
 
  • Time
  • Show
Clear All
new posts

  • Wrath
    replied
    Originally posted by running_cold924
    Would one for a urs4/6 work? I just did this conversion to my car, used one from an a6.

    Leave a comment:


  • marius555
    replied
    Dear friends.

    After changing about 7 ( seven ) a8 d2 boosters i managed to solve the issue using the adapter received from Alex.

    Very important : DO NOT USE OLD PUMPS / BOOSTERS ! If it has been stored outside or on a shelf somewhere its most likely going to fail ... if you buy a sh one make sure that is on the car and the pump has the reservoir attached and brake fluid into it otherwise you will have to change it again and again ....

    I used A4 B7 booster and its pump. The result its amazing and i am very happy with it .


    Shopping list :

    - Alex ( Error404 ) kit for urS
    - 8E0 612 105 N booster with pump
    - brake lines from a4 B7 ( the angle of the brake pump is different than stock and these ones from b7 really look nice ).
    - as much beer as possible :-)


    Have a nice day
    Marius

    Leave a comment:


  • running_cold924
    replied
    No problem. Like I said I have an extra, just rebuilt. If you are in Canada I can ship it to you. I had 2 used ones leak on me (sucking vacuum around the center bore seal) and finally found a good reman version. If interested just send me a PM.

    Leave a comment:


  • etsola
    replied
    Originally posted by running_cold924
    This was directly off a 96 a6 with the 2.8. I think the last letter is P. Was very worn when I purchased it. Here is another

    https://www.ebay.co.uk/itm/Brake-boo...cAAOSwT4ZbFwjJ
    Thanks buddy

    Leave a comment:


  • Error404
    replied
    Just to be clear, LHD and RHD have different considerations for the vacuum conversion.

    The RHD cars can only use the smaller diameter servo/booster due to proximity to the turret, so be sure you are buying the right parts.

    Leave a comment:


  • running_cold924
    replied
    This was directly off a 96 a6 with the 2.8. I think the last letter is P. Was very worn when I purchased it. Here is another

    https://www.ebay.co.uk/itm/Brake-boo...cAAOSwT4ZbFwjJ

    Leave a comment:


  • etsola
    replied
    This part # doesn't bring back any results ...
    I found 4A0 612 107 A
    A6 from '95 to '98 ?

    Thanks

    Leave a comment:


  • running_cold924
    replied
    4A0612105 is what I used. I do have a fresh rebuilt one too.

    Leave a comment:


  • etsola
    replied
    Originally posted by running_cold924
    Would one for a urs4/6 work? I just did this conversion to my car, used one from an a6.
    Do you have a part # by any chance

    Leave a comment:


  • Error404
    replied
    Here is another option

    Leave a comment:


  • Bowie69
    replied
    Cabriolet has a vacuum system, the hydraulic system was only fitted to the 5-pots.

    Leave a comment:


  • running_cold924
    replied
    Would one for a urs4/6 work? I just did this conversion to my car, used one from an a6.

    Leave a comment:


  • etsola
    replied
    I thought the Cabriolet was the exact same thing as the 90 ... so with hydraulic brake system ... No ?

    So ... What is the important part ?

    The diameter of the master cylinder needs to match the one of the Servo (Brake Booster) ?

    i.e. 7a Coupe Quattro has a 25.4mm master cylinder ... can I take any brake booster that has that diameter ? Can other (for example smaller) brake booster be fitted ?

    Because there seem to be the VW T4 that has a 25.4mm master cylinder as ours ... will this work ?

    Thanks
    Last edited by etsola; 13 March 2019, 15:55.

    Leave a comment:


  • Bowie69
    replied
    Did you get the cabriolet there? Then yes....

    Leave a comment:


  • etsola
    replied
    Any input for parts Available in North America ?

    Leave a comment:

Working...