Hydraulic to Vaccum servo conversion

Collapse
This is a sticky topic.
X
X
 
  • Time
  • Show
Clear All
new posts

  • Bowie69
    replied
    B3 no, B4 yes, I think.

    When I got mine for my B3 CQ20V I asked that the servo came with the bracket and any pipework to save hassle, however I didn't need the bracket, as my Coupe had one already fitted

    Leave a comment:


  • A80Avant
    replied
    Originally posted by audiman
    This thread is a mess!!! The OP I assume, as its not stated, is converting a LHD car?? Also, multiple people taking about fitting different servos on LHD and RHD non-S2 models!!!!

    Can someone give a parts list required to convert a RHD S2 car to vacuum servo??

    I am assuming that servo 8a2612105a is the required part and then there is the mounting bracket, is that or not required?
    When I posted this I did use the document from the US, so an LHD car which you can see from the attached pdf. I didn't follow what others wrote about the RHD process, sorry

    Leave a comment:


  • audiman
    replied
    This thread is a mess!!! The OP I assume, as its not stated, is converting a LHD car?? Also, multiple people taking about fitting different servos on LHD and RHD non-S2 models!!!!

    Can someone give a parts list required to convert a RHD S2 car to vacuum servo??

    I am assuming that servo 8a2612105a is the required part and then there is the mounting bracket, is that or not required?

    Leave a comment:


  • Pirvu Eugen
    replied
    I measured now at my 200 and the rod deflection is 10mm.
    This explains why this failure happens only in C3..C4 chassis with these servos.

    Leave a comment:


  • LHD_Kid
    replied
    I've just measured the coupe... the deflection of the rod from straight is around 1mm

    I don't think this issue affects the conversion on an S2 for example.....

    Leave a comment:


  • LHD_Kid
    replied
    Originally posted by Pirvu Eugen
    Dont think so... i searched and nothing came up. Not as the new mercedes ones.
    I think that poppet valve rubber thing is not working ok with high rod angles.
    So, the answer really is to replace the standard fork which connects to the pedal with an eccentric one which can move the pivot point over the required amount to keep the pushrod going straight into the servo unit.

    Looks like its between 5 and 10mm, will measure more accurately next week and get something made.

    I wonder if just doing this will work, without having to swap the booster out.........

    Leave a comment:


  • Pirvu Eugen
    replied
    Dont think so... i searched and nothing came up. Not as the new mercedes ones.
    I think that poppet valve rubber thing is not working ok with high rod angles.

    Leave a comment:


  • LHD_Kid
    replied
    Are the twin ones so prone to failure when they are in their original habitat? I mean, does an S8 or RS6 suffer a lot from servo failure, or is it just when they are messed with?

    Leave a comment:


  • Pirvu Eugen
    replied
    Off... yes... the dual diaphragm one is more complicated and prone to failure as the single one..
    Thank you Des for feedback!
    Last edited by Pirvu Eugen; 26 March 2017, 06:53.

    Leave a comment:


  • diesel des
    replied
    I gave up on the twin servos after having so many leak in my urs4. Using an a6 single vacuum unit now.

    Sent from my LG-H955 using Tapatalk

    Leave a comment:


  • Pirvu Eugen
    replied
    I spoke with LhdKid about this issue and he suggested to make an excentric pedal adapter
    to maintain the same piston travel as before...because installing the pin higher on the pedal will shorten the piston travel..and i dont want this.
    Last edited by Pirvu Eugen; 25 March 2017, 12:07.

    Leave a comment:


  • Pirvu Eugen
    replied
    apparently...is an issue with these double diaphragm types into the c3 c4 chassis.
    Is starange that into these chassis were also vacuum units with the same brake pedals. But single diaphragm type. The single type ,maibe, is accepting bigger rod angles.
    The only thing can go wrong in this matter is the valve poppet.
    What you think?
    Attached Files

    Leave a comment:


  • marius555
    replied
    Dear friends. I am at this moment with the 4'th booster ( a8 d2 ). As mentioned above , it literally screams in the car....

    I assume at this moment that the brake pedal angle isn't right so it's destroying a sealing or something .

    Just talked with Pirvu Eugen on here and he measured that the mount on the pedal si 10mm down than it should be and this might be the cause...


    Attached Files

    Leave a comment:


  • Error404
    replied
    Can you post pictures of the bolt pattern on your bullhead and the servo?

    Leave a comment:


  • hiloran
    replied
    A8 servo fits nicely. Bolt pattern is same.

    ...edit. sorry after reading post again. Seem to be old info
    Last edited by hiloran; 8 July 2015, 19:54.

    Leave a comment:

Working...